3. Solve the following problemThe following shaft is subjected to three torsional moments expressed as a fraction of T. Determine the maximum value ofthe T if the allowable shear stress is Tallow 80 MPa. Draw the torsion (torque) diagram along the shaft for that value of T,and determine the relative angle of twist between sections A and C (use a shear modulus G = 26GPa).=diameter d 60mmTallow 80MPaG = 26 GP₂Req'd: allowable torque Tangle of twist of A relative to C PAICTorsion diagram1.2m1.2m

Answered: 3. Solve the following problem The…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question-04: Solve for the torque T that can causes a maximum shearing stress of 4.2 ksi in the cylindrical steel shaft as shown in Figure 3. Assume radius of the shaft r = 1.2inches.
An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t - 18 mm C t Y ▼ 2 Find the dimension c of the cross section such that it will satisfy the allowable stress. Select the correct response: 318.329 mm 290.593 mm 355.903 mm 263.312 mm
Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque) and a tensile force, the axial tensile stress is 30 MN m-2 and the shear stress 50 MNm (Figure). Estimate the principal stresses and draw the inclined element with the principal stresses r= 6 mm d = 30 mm Y-face 50 X-face D= 40 mm. 30MN m2 30 50 MN m-
2. The lengths LAB = LBC = 200 mm and LCD = 240 mm. The diameter of parts AB and CD of the bar is 25 mm and the diameter of part BC is 50 mm. The shear modulus of the material is G = 80 GPa. What value of the %3D torque T would cause the angle of twist of the right end of the bar relative to the wall to be zero? 4 kN-m A 8 kN-m LAB B T LBC.
2.0 in 3.0 in. The tubular torsional shaft shown above is made ofa stainless steel metal with the following properties: E = 28500 ksi • G= 11000 ksi • v = 0.37 If the pipe cross-section is subjected to an internal torque of T 50 kip-in, which of the following is closest to the minimum shear stress action on the cross-section? 3.92 ksi 1.57 ksi 7.84 ksi
A solid 1.40-in.-diameter steel [G = 12,000 ksi] shaft is subjected to the torques shown. Determine the magnitude of the maximum shear stress in shaft segment (1). a 1.82 ksi b 2.45 ksi c 3.86 ksi d 3.01 ksi e 2.85 ksi
2.pdf A solid aluminum shaft (2 in) in diameter is subjected to two torques as shown in Figure below. Determine the maximum shearing stress in each segment and the angle of rotation of the free end. Use G = 4 x 106 ps 200 Ibft 800 bft 2 ft 3 ft - Determine the maximum stress in the member CD if you know that the distributed load W = 40 kN/m, the diameter of member CD is 45 mm and E=200 GPa.
As seen in the figure, ABC rod with end-A fixed support pipe section has an outer diameter of 30 mm and an inner diameter of 24 mm. 50 N force at an angle of 30 ° with the y-axis at the free end C to the ABC rod is implemented. (a)Show and calculate the cross-sectional effects on the cross-section a a. (b) Calculate the stresses occurring at the H point of the ABC bar and calculate these stresses
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
3:30 51 Photo Done Problem 1: A round solid shaft is subjected to torsion as shown. Find: 1- Maximum torsional shear stress of the steel and aluminum shafts. 2-Angle of twist at point C. Steel G = 30.0x106 psi 3" Radius Steel 2" Radius Aluminum π/ DA Aluminum G = 15.0x105 psi A B T₁ = 50 k-ft T₂ = 20 k-ft 8 ft 12 ft + T2 +
1. The compound shaft shown in the figure is attached to rigid supports. For the bronze segment AB, the maximum shearing stress is limited to 8000 psi and for the steel segment BC, it is limited to 12 ksi. Determine the diameters of each segment so that each material will be simultaneously stressed to its permissible limit when a torque T-12 kip-ft is applied. For bronze, G = 6x106 psi and for steel, G = 12x10 psi. Bronze Steel 4 ft 6 ft THARAN
Q4/ Determine the moment M that must be applied to the beam in order to create a maximum stress of 90 MPa. Also sketch the stress distribution acting over the cross section. 300 mm 20 mm M 260'mm 30 mm 30 mm 20 mm 30 mm

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS