3. An aluminum material element experiences a state of plane stress with the magnitudes and directions of the stress components given in the figure. Please calculate the change in volume per unit volume this material element would experience when subjected to the stress state given in the image below and a temperature increase of 80°C. (Note that the dotted horizontal line and 15 degree angle are irrelevant to this problem). Aluminum Properties: Thermal Coefficient of Expansion = 24 x 10-6 mm/mm/°C, Elastic Modulus = 69 GPa, Poisson Ratio = 0.35 250 MPa 60 MPa 15° 150 MPa

3. An aluminum material element experiences a state of plane stress with the magnitudes and directions of the stress components given in the figure. Please calculate the change in volume per unit volume this material element would experience when subjected to the stress state given in the image below and a temperature increase of 80°C. (Note that the dotted horizontal line and 15 degree angle are irrelevant to this problem). Aluminum Properties: Thermal Coefficient of Expansion = 24 x 10-6 mm/mm/°C, Elastic Modulus = 69 GPa, Poisson Ratio = 0.35 250 MPa 60 MPa 15° 150 MPa

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
1.4-7 The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13 mm and a gage length of 50 mm (see figure for Prob. 1.4-3). At fracture, the elongation between the gage marks was 3.0 mm and the minimum diameter was 10.7 mm. Plot the conventional stress-strain curve for the steefor the steel and determine the proportional limit, modulus of elastics of elastic- ity (i.e., the slope of the initial part of the stress-strain,tress-strain curve), yield stress at 0.1% offset, ultimate stress, percent, elongation in 50 mm, and percent reduction in area. 'ess, percent area. TENSILE-TEST DATA FOR PROB. 1.4-7 Elongation (mm) 0.005 0.015 0.048 Load (kN) 5 10 30 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
Q stress determination in beams., Solid.
An aluminum alloy [E = 67 GPa; ν = 0.33; α = 23.0 × 10–6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 225 mm, a cross-sectional area of A = 5100 mm2, and a length of L = 4.1 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by ΔT = 63°C, the longitudinal normal strain in the plate is found to be 2900 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Δd.
The stress parallel to the surface of the material is called_ A Shear Stress B Normal Stress c) Bearing Stress D None of the choices
The following information about the o-e curve is given for a steel alloy. E = 0.001527 at o = 300 MPa and ɛ = 0.003054 for o = 600 MPa. (a) Draw the stress-strain diagram and calculate the E for this alloy.
this is about thermal stress
An element in plane stress is subjected to stresses o, = -8400 psi, ay = 1100 psi, and ty = 1700 psi (see figure). The material is aluminum with %3D modulus of elasticity E =10,000 ksi and Poisson's ratio v = 0.33. Determine the following quantities: (a) the strains for an element oriented at an angle 30 degrees, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements. Ty Txy Ox
The topic is all about thermal stress. Please use pen and paper to solve and show the conversion in the solution. In solution: Show the relationship in deformation:
A steel 0.6 inch×1.2 inch steel 90 m long is subjected to a 45 KN tensile load along its lenght.If poison's ratio is 0.3 Find: A. The deformation along its lenght. B. The deformation along its thickness. C. The defirmation along uts width. D. The lateral strain.
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E=69 GPa If Poisson's Ratio is 0.33, what will be the lateral strain? E=68 v=-e(lateral) e(axial)
1. An aluminum rod is rigidly attached between steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa.