3. A voltage source with internal resistance, 40 and load resistance, 60 is shown in figure 3. A 50 V RL=60 B Figure 3 Using source transformation find the equivalent current source.
Q: determine the solution for x and y if (5x+j10)(2+jy) =90 - j70
A:
Q: A conducting plate of thickness d carrying the current density of the field is placed in a region wi...
A: Answer -
Q: 1. Simplify the following using basic laws of Boolean algebra: a) Y = ABC + ABC + ABC + ABC+ĀBC + AB...
A: Note: As per the guide lines of the bartleby we are supposed to solve 3 questions, when they are i...
Q: SUPERMESH
A: Solution
Q: c) Determine the output voltage Vout of the circuit shown in figure 10 n 2 ka 2 mvo s kn ww 4kn 15 s...
A: The solution is given below
Q: DESIGN 1. Based on the given state Diagram, design a sequential circuit using Rs Flip-Flop. 0/1 00 1...
A:
Q: Is The ac sine wave supplied to the motor artificially produced by an inverter stage in the Flux vec...
A: Given, Regarding to the sine wave supply to the motor. Yes it is artificially produced by an inverte...
Q: A transformer is rated at 890 VA and has a primary voltage of 440 V and a secondary voltage of 180 V...
A: Given: A transformer is rated at, S = 890 VA Primary voltage, V1 = 440 V Secondary voltage, V2 = 18...
Q: 73.333 2 R. Figure (b) H.W: Find the equivalent resistance between terminals a & b in figure below. ...
A:
Q: 240 N 150 N RT 120 Q 360 N b. R7 4Ω 8 Ω 8Ω GT с. Brown Black Gray Red Red Gold Orange White RT Orang...
A:
Q: 5. Determine the transfer function using Mason's Gain formula GA G G2 R(s) No N N Ge Gs Fig. 5
A:
Q: Explanations of the mechanics and applications of motors and generators.
A: Mechanics is a branch of science that studies how objects move when they are subjected to force. It ...
Q: 2. The series is shown in the picture below, i(t) = 2 + 10 Cos(t+10° ) + 6 Cos(3t + 35°) Amperre., ...
A: The solution is given below
Q: мCQ 12 An ideal step-down transformer has 200 primary turns and 50 secondary turns. If 440 yolts (rm...
A: Given: An ideal step down transformer has, Primary turns, N1=200 Secondary turns, N2=50 Primary volt...
Q: "Determine the dc resistance in ohms of commercially available silicon diode at a forward current of...
A: Given: The voltage across a forward biased silicon diode is, V=0.7 V Forward current, I = 4 mA
Q: A two-anode mercury-arc rectifier delivers a load of 5.98kw at 115volts. If the primary of the tran...
A:
Q: The below diagram shows the De-Sauty method to measure the unknown capacitance (C). Then C, is given...
A: Circuit diagram is given as, Here, R1 and R2 are resistance C is standard capacitance, Cx is capaci...
Q: Describe the importance of Fourier series and Laplace transform
A: The Fourier and Laplace transforms are connected. The Fourier transform converts functions or signal...
Q: Three identical capacitors are connected in delta to a 408 V, 50Hz, 3-phase supply. If the line curr...
A:
Q: A 100 V power supply has a series limiting resistor of 100 kN connected to its output. Draw the Nort...
A: Consider the circuit for the required specification.
Q: Q-5) A unity feedback system has the following forward transfer function: 1000(s + 8)(s + 12) s(s+ 1...
A: In this question, Open loop transfer function is given with unity feedback system. determine the ty...
Q: Find the Currents in all branch in net shown? 3A 3A Noter Convert the Qurrends SouYce in to Vo ldaye...
A: The solution is given below
Q: Analyze the output voltage Vo in the network efficiently for sinusoidal input signal Vi shown in Fig...
A:
Q: A three-phase transformer, connected in star-delta, is composed of three single-phase transformers, ...
A: Given, A 3-phase transformer, connected in star-delta, is composed of 3 single phase transformers, e...
Q: 6. A circuit consists of four resistors connected in parallel and connected to a 20-V source as show...
A: From given colour coding find the resistance of each resistor. Power observed =(voltage across the ...
Q: A voltmeter having an accuracy of ±3 percent of full-scale 250 V range is employed to read 150 V. Th...
A:
Q: hat is the Frequency oF liq b7 thataltaws electrons +obe released Sroyabme tel that has a Wols E Fat...
A:
Q: Q-5) A unity feedback system has the following forward transfer function: 1000(s + 8)(s + 12) s(s+ 1...
A: In this question, We need to determine the type of the system and position constant kp, velocity co...
Q: 5) Design a linear suturated load inverter shown in the below figure with VDD= 3.3V,VL = 0.2V and P ...
A: The inverter is the nucleus of all really digital designs. Once its function and properties are clea...
Q: A 400V, 3-phase Induction motor has input power of 12 KW and operates at power factor of 0.87 laggin...
A: Let W1 be one wattmeter reading and W2 be another wattmeter reading. Input power W1+W2. Reactive po...
Q: Q12: A. Explain the relation between current and voltage in the basic component of electrical circui...
A: Answer (A): The basic components of electrical circuits are, Resistor (R), Inductor (L), and capacit...
Q: 5. Suppose for x(n) y(m) + 2 that X(w) for -A <w<T is given by X (w) 2 -T Sketch Y (w) for -T <w<T. ...
A:
Q: FNo ho Qnd thu Maaimum Bwen then Cror Bo Trois kred.
A:
Q: The circuit shown in Figure P has three inputs: v1, i2, and v3. The output of the circuit is the cur...
A: This question belongs to circuit theory . It is based on the concept of nodal analysis . This analys...
Q: clectVon rakceis a Jubsta-
A: Solution Definition of free electron 1 : an electron within a conducting substance (as a metal) but ...
Q: Identify whether the following are linear and time-invariant. Show proofs. 1.) y(t)=x(3t+2) 2.) y[n]...
A:
Q: 4.49 determine the currents indicated in the circuit shown below. solve for a. Rₜ b. I₁ c. l₁ up...
A:
Q: 3. A conductor 120 cm long and carrying a current of 10 A, lies at right angle to a magnetic field o...
A:
Q: Does a normally open contact act as a switch to pass power when the status of its referenced compone...
A: Consider the two type of contacts used in the industrial environment are normally open and normally ...
Q: EXAMPLE 3. A 25-kw three-phase oonverter has a d-o output voltage of 230 volta. Asuming negligible l...
A: Example 3) number of phases, m=3 power factor, pf =1 negligible loss hence efficiency, η =100 %=1 ...
Q: Ohm's Law calculates what values? Please
A:
Q: a. h[n] = u[n], where u[n] = unit step Above defines the impulse response h[n] of a certain LTI sys...
A: The solution is given below
Q: How to make a circuit drawing diagram of an energy saving switch for a kettle?
A: KETTLE Kettles are one of the most basic kitchen gadgets. When you lift the lid and look inside, you...
Q: E = 20 V R1 3 Ω o E, = 15 V 12 R233 0 Va R4 R5 .6Ω R,.
A: The value of current I1 is given directly as: I1=20-153=1.67 A The value of current through R4 is gi...
Q: How do you know the polarity? 50v 47050 - Know way of knowing · Lettering · Silver strip on Negative...
A: One can determine the polarity of the capacitor by the terminals of the capacitor, the labeling of t...
Q: In the circuit shown in the given figure, the current through inductor is 10 2 10 V 5H 5 V
A: Given circuit,
Q: e. Given Vcc=80V, R2=1602, B=100, VBB=6V. Flip the switch to close, nd Iz=0.002A, 1) Determine Rg- 2...
A:
Q: Determine the operating power factor of a 6.6kV Y-connected synchronous motor has a synchronous reac...
A: Givenlet δ be the excitation angleThen excitation voltage Ef=6.6∠δ°KvInduced voltage V=5.16Kv/ph
Q: Resistor Value Identification from Color Coding and Verification by Measurement
A: The resistor value can be calculated by using the resistor color coding table and the sam can be ver...
Q: 4.54.1 In the circuit shown in the image below, if Ro = 1.5 k2, Rx= 51 Q, and V1 2.0 V, determine th...
A:
Step by step
Solved in 2 steps with 2 images
- What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mARefer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
- For the circuit below, determine the resistor current. The source is 8 volts, the Zener potential is 5.2 volts and the resistor is 5k ohms.B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mAA chopper is employed to charge a battery as shown in figure. The charging current is 5 A. The duty ratio is 0.2. The chopper output voltage is also shown in the figure. The peak to peak ripple current in the charging current is https://practicepaper.in/wp-content/uploads/GATE/EE/20031/q87.jpg
- is made from a combination of A mixed resistors circuit as shown in Figure parallel and series circuits. The values of the resistances mentioned in the circuit are in Ohm (2) and the supply voltage is in Volt (V). Determine the: (i) Current through the circuit (I). (ii) Voltage drop (V) across the circuit. 0.6 0 4 0 0.5 0When properly biased in the ohmic region, a JFET exhibits the properties of a variable resistance. True FalseQuestion 3: A reference current of 0.3mA is given. Make a current mirror circuit which provide currents of 0.2mA and 0.3mA.