3) The electric motor exerts a torque of 600 N.m on the steel shaft ABCD when it is rotating at a constant speed. Design specifications require that the diameter of the shaft be uniform from A to D and that the angle of twist between A and D not exceed 1.5°. Knowing that t max < 65 MPa and G = 77 GPa, determine the minimum diameter the shaft 200 N.m 400 N.m 0.5 m that can be used. 08m -0.3m

3) The electric motor exerts a torque of 600 N.m on the steel shaft ABCD when it is rotating at a constant speed. Design specifications require that the diameter of the shaft be uniform from A to D and that the angle of twist between A and D not exceed 1.5°. Knowing that t max < 65 MPa and G = 77 GPa, determine the minimum diameter the shaft 200 N.m 400 N.m 0.5 m that can be used. 08m -0.3m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The electric motor below, exerts a torque of 800 N.m on the steel shaft ABCD when it rotates at constant speed. Design specifications require that the shaft diameter be uniform from A to D and that the angle of twist between A and D not exceed 1.5°. Knowing that tmax < 60 MPa e G = 77.2 GPa, determine the minimum shaft diameter that can be used. 300 N-m 500 N-m B D 0.4 m 0.6 m 0.3 m
Q: For the aluminum shaft shown (G 27 GPa), determine (a) the torque T that causes an angle of twist of 4° (b) the angle of twist caused by the same torque T in a solid cylindrical shaft of the same length and cross-sectional area. 1.25 m 18 mm 12 mm
Q3: The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques as shown in Fig. 3. A 44-mum-diameter hote has been drilled into portion CD of the shaft. Knowing that the entire shaft is made of steel for which G-77 GPa, determine the total angle of twist at end A. & 06m 60 mm 2000 0.2m Fig. 3 0.4m 250 №-m
3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft, and (b) the angle of twist of end D relative to end A. If the desired angle of twist of end D to end A is 1º, determine (c) the power the motor should transmit considering the same rotational speed. Also, determine (d) the maximum stress in the shaft. Use G = 12 x 10° psi for steel, and assume that friction at bearing D is negligible. A 4 in. 3.5 in. 3.5 in. Tmax ID ODIA B C 6 ft - 4 ft- - 2 ft Tmax OD/A
The allowable shearing stress is 15 ksi in the 1.5-in.-diameter steel rod ABand 8 ksi in the 1.8-in.-diameter rod BC. Neglecting the effect of stress concentrations, determine the largest torque that can be applied at A
HW1: The vertical shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into a portion CD of the shaft. Knowing that the entire shaft is made of steel for which G = 80 GPa. Determine the angle of twist at end A with respect to D (i.e 0 AD). 250 N-m 3000 N-m 0.4 m B 0.2 m 44 mm- 0.6 m -60 mm
3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft, and (b) the angle of twist of end D relative to end A. If the desired angle of twist of end D to end A is 1°, determine (c) the power the motor should transmit considering the same rotational speed. Also, determine (d) the maximum stress in the shaft. Use G = 12 x 10 psi for steel, and assume that friction at bearing D is negligible. 4 in. 3.5 in. 3.5 in. Tmax -6 ft B C 4 ft 2 ft k ⒸD/A Tmax ⒸD/A
Compound shaft ACB is fixed at A and consisting of two solid circular sections AC & CB, as shown, and is subjected to the given distributed torque. The diameter of part AC is D1, and the diameter of part CB is D2. The material of the shaft having a shear modulus of 69 GPa. Determine (a) the maximum shear stress (KPa) developed in shaft AB, (b) the angle of twist of point B. The values of L1, L2, D1, and D2 are given in table below for each student. D1 D2 50 Nm/m A B 0.2 m L1 L2 =l13 mm 1.3 L2=0,7 mm 80mm 60mm D, =
30 mm PROBLEM 3.36 30 mm The torques shown are exerted on pulleys B, C, and D. Knowing that the entire shaft is made of steel (G = 27 GPa), determine the angle of twist between (a) C and B, (b) D and B. 400 N. m 36 mm 900 N- m 36 mm 500 N- m u 90. 0.8 m 1 m 0.5 m PBC = 8.54° PBD = 2.11° %3D
Knowing that the lengths of the shown solid shafts are AB=60mm and BC=80mm, determine the torque TA if the total angle of twist of disk A relative to the ground C is 3°. What are the corresponding shearing stresses for each shaft? Take G=77 MPa. TA 30 mm B Tg = 400 N . m 46 mm
2. In the gear system shown, the motor applies a torque of 600 N-m to the gear at A. Shafts (1) and (2) are solid shafts, and the bearings shown allow free rotation of the shafts. (a) Determine the torque TE provided by the gear system at gear E. (b) If the allowable shear stress in each shaft must be limited to 70 MPa, determine the minimum permissible diameter for each shaft. 72 teeth B 24 teeth (1) 30 teeth 60 teeth (2) E
400 mm 625 mm 1. The aluminum rod, AB (G = 27 GPa), is bonded to a brass rod BD (G = 39 GPa) and torques, TA = 800 Nm and Tg = 1600 Nm are applied as shown to the right. The diameters of AB is 36 mm and the diameter of BD is 60mm. Determine (a) the twist of point B, ø8, and (b) the twist of point A, Øa. Ans: Ø = + 3.541°, øs = -0.577° TA TB Fixed to wall