3-phase, 2-pole, Y-connected synchronous motor runs at 750 r.p.m. The excitation is constant and corresponds to rcuit terminal voltage of 1000 V. The resistance is negligible as compared with synchronous reactance of 1.50 per ermine the power input, power factor and torque developed for an armature current of 100 A.

3-phase, 2-pole, Y-connected synchronous motor runs at 750 r.p.m. The excitation is constant and corresponds to rcuit terminal voltage of 1000 V. The resistance is negligible as compared with synchronous reactance of 1.50 per ermine the power input, power factor and torque developed for an armature current of 100 A.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- To control the speed of an induction motor, the supply frequency is reduced by 10%. For the same magnetizing current to remain constant, the supply voltage must be....... a) Reduced by 10%, b) Reduced by 20%, c) Increased by 10%, d) Increased by 20% 2. When maximum starting torqua ic ohtoinod
A 2300-V, 3-phase, wye - connected, round rotor synchronous motor has a synchronous reactance of 3 ohms per phase and an armature resistance of0.25 ohm per phase. The motor operates on load such that the power angle is -15 degrees, and the excitation is so adjusted that the internally induced voltage is equal to the magnitude of the terminal voltage. Determine the armature current.
A 20 hp, 250 V shunt motor has an armature circuit resistance (including brushes and interpoles) of 0.22 Q. and a field resistance of 170 Q. At no-load and rated voltage, the speed is 1200 rpm and armature current is 3.0 A. At full-load and rated voltage, the line current is 55 A, and the flux is reduced 6% (due to the effects of armature reaction) from its value at no-load. What is the full-load speed? 100 гpm 1220 грm 1000 гpm 120 гpm
(b) A 2 pole 220 V, 100A, and 850 rpm separately excited DC motor has an armature resistance of 0.15 0. Two field coils are connected in parallel and used to drive a load with the torque of TL = 400 – 0.2N, Nm Where N is the motor speed in rpm. Armature voltage control and two field windings connected in series are used in speed control below and above the rated, respectively. (i) Calculate the motor armature current and speed when the armature voltage is reduced to 110VV. (ii) Examine the motor speed and current when field coils are connected in series.
A 4-pole, 400V, 10kW slip ring 3-phase induction motor has motor resistance of 0.16ohm/phase and its standstill reactance is 0.27 ohm/phase. The voltage across the slip rings at standstill is 141V per phase. The motor develops a torque of 62.4Nm at a slip of s A) 0.035 and the rotor current 31.1A. Find the magnitude and phase of emf to be injected to the rotor circuit so that the motor runs at s. B) 0.02 and develops the same torque
A 10 kW, 250 V Shunt motor has an armature resistance of 0.5 ohm and a field resistance of 200 ohm. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3 A. At full load and rated voltage, the line current Is 47 A and because of armature reaction, the flux is 4 % less than it no load value. a.) What is the full load speed? b.) What is the developed torque at fll load?1158 rpm
A 10 kW, 250 V Shunt motor has an armature resistance of 0.5 ohm and a field resistance of 200 ohm. At no load and rated voltage, the speed is 1200 rpm and the armature current is 3 A. At full load and rated voltage, the line current is 47 A and because of armature reaction, the flux is 4 % less than it no load value. a.) What is the full load speed? b.) What is the developed torque at full load?
A 460-V, 25-hp, 60-Hz, four pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R1 = 0.6410 X1 = 1.1060 The total rotational losses are 1100 w and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.2 % at the rated voltage and rated frequency, find the motor's a) Speed R2 = 0.3320 X2 = 0.4640 XM = 26.30 d) Peony and Pout e) Tind and Tload f) Efficiency b) Stator current ) Power factor
4. The synchronous reactance of a synchronous motor is 102 per phase and its armature resistance is negligible. The input power is 1500kW, and the induced voltage is 4600V. If the terminal voltage is 4160 V, determine a) The armature current, and b) The power factor.
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
A 230V dc shunt motor has armature and field resistances of 0.3 W and 140 W respectively. Calculate the induced emf and the torque developed by the motor when it runs at a speed of 800 rev min-1 and the armature current is 2A. To drive a larger load at 1000 rev min-1 an additional resistance, R is connected in series with the field winding. In this situation the armature current is 30A. Calculate the new induced emf and torque and the value of R. Assume that the flux is directly proportional to the field current
An 3-phase induction motor(IM) has full load slip = 0.5%. If the rotor circuit resistance is increased so that R2new =2R2old, then the slip at which the motor develops the same full load torque is=.. * ......