3-19 Consider a 1.2-m-high and 2-m-wide double-pane win- dow consisting of two 3-mm-thick layers of glass (k = 0.78 W/m . °C) separated by a 12-mm-wide stagnant air space (k = 0.026 W/m. °C). Determine the steady rate of heat transfer through this double-pane window and the temperature of its inner surface for a day during which the room is maintained at 24°C while the temperature of the outdoors is -5°C. Take the convection heat transfer coefficients on the inner and outer Glass 3 12 3 mm Frame FIGURE P3-19 = surfaces of the window to be h₁ = 10 W/m² °C and h₂ 25 W/m². °C, and disregard any heat transfer by radiation.

3-19 Consider a 1.2-m-high and 2-m-wide double-pane win- dow consisting of two 3-mm-thick layers of glass (k = 0.78 W/m . °C) separated by a 12-mm-wide stagnant air space (k = 0.026 W/m. °C). Determine the steady rate of heat transfer through this double-pane window and the temperature of its inner surface for a day during which the room is maintained at 24°C while the temperature of the outdoors is -5°C. Take the convection heat transfer coefficients on the inner and outer Glass 3 12 3 mm Frame FIGURE P3-19 = surfaces of the window to be h₁ = 10 W/m² °C and h₂ 25 W/m². °C, and disregard any heat transfer by radiation.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.53P: Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed...

See similar textbooks

Similar questions

Q3) Consider a 1.2 m high and 2 m wide double pane window shown in Figure, consisting of two 3 mm thick of glass ( k 0.78 W/m."C) separated by a 12 mm wide stagnant air space (k = 0.026 W/m."C).Determine the steady rate of heat transfer through this double %3D pane window and the temperature of its inner surface for a day during which the room is maintained at 24 °C while the temperature of the outdoor is -5 "C. Take the convection heat transfer coefficients on the inner and outer surfaces of the window to be hi Amm = 10 W/m2.C hz = 25 W/m2."C. Prae
A window is made up of two panes of glass (with surface temperatures of 15 oCand 5 oC) that are separated by a gap of 3 cm. The said window has a height of2 m and a width of 5 m. Initially, the gap is filled with air (flowing via temperaturegradient). Then, this air space is partially evacuated such that the pressure isalready 0.1 mpa. This is done to lessen the heat transfer between the two panes ofglass. Both glass surfaces have an emissivity of 0.9. Calculate the rate of heattransfer (W) through the panes.
Convection 2. For a boiling process such as shown in Figure below, the ambient temperature Tin Newton's law of cooling is replaced by the saturation temperature of the fluid Tsat. Consider a situation where the heat flux from the hot plate is q=20 x 105 W/m². If the fluid is water at atmospheric pressure and the convection heat transfer coefficient is hw=20 x 103 W/m2 K, determine the upper surface temperature of the plate, Ts, w. In an effort to minimize the surface temperature, a technician proposes replacing the water with a dielectric fluid whose saturation temperature is Teat, d=52 °C. If the heat transfer coefficient associated with the dielectric fluid is h = 3 x 103 W/m2 K, will the technician's plan work?
Palm oil with a density of 1200 kg/m3 and the specific heat of 2 kJ/(kg.K) is to be heated from 20oC to 80oC before further processing. The oilplaced in a vessel (vessel) cylindrical upright with a diameter of 2 meters.The height of the oil vessel inside is 2 meters. For this purpose, an electric heating element with an electrical resistance type of heat is used.The electrical resistance used is a 2 mm diameter conductor wire wrappedwith magnesium oxide material with a thermal conductivity of 0.4 W/(m.K) thick 2.5 mm, then coated with the outermost metal 0.5 mm thick. Occurring power density on the outermost metal layer should not be more than 25 kW/m2. Warm-up time is expected to be only about 1.5 hours. Calculate: a) Required electrical power? (in kW) b) Rating of the heater by meter length? c) Maximum temperature of the heater element?
A 2-kW resistance heater wire with thermal conductivity k = 15 W/m - °C, di- ameter D = 0.4 cm, and length L = 50 cm is used to boil water by immersing Water it in water (Fig. 2-19). Assuming the variation of the thermal conductivity of the wire with temperature to be negligible, obtain the differential equation that de- scribes the variation of the temperature in the wire during steady operation. Resistance heater
A cyclic process consists of two isothermal and two isobaric processes. Calculate the network done on the sytem in this cyclic process.
350 pipes are fixed as square in a pipe bundle used for condenser. PipeThe outer diameters are 8 mm and the steam at 0.2 bar is desired to be condensed on the pipes. pipe outer The surface temperature is kept constant at 30 °C. If the length of the pipes is 1.5 m, the heat transferred in the systemCalculate the amount of energy and the amount of condensed steam
Water is entering a heated tube at mass ow rate of 1.2 kg/s. The temperature at the inlet is 20 C and at the outlet is 80 C. Assume the surface temperature of the tube is 100 C. The convection coe cient of the water ow is 28 W=m2 C. The speci c heat and density of water can be assumed to be 4180 J=kg C and 990 kg=m3. What is the rate of heat transfer to water during this proces
A cylindrical storage tank with diameter of 4m and a length of 10 m will hold a fluid whose temperature must be maintained at 347k. in order to size the heater required for the tank the following worst-case scenario is considered: Ambient temperature=-20 wind speed=20m/s tank wall temperature=347k what size (kW) heater will be needed?
A steel plate of thermal conductivity 50 W/mK and thickness 10 cm passes a heat flux of 30 kW/m2 by con- duction if the temperature of the hot surface is 100°C then what is the temperature of the cooler side of the plate (A) 40°C (С) 60°C (В) 50°C (D) 70°C
0.809 and 0.795 3-176 The overall heat transfer coefficient of a wan s determined to be U= 0,425 W/m-°C under the condi- tions of still air inside and winds of 12 km/h outside. What will the U-factor be when the wind velocity outside is doubled? Answer: 0.428 W/m-°C ransler olls of
A square thermal window is constructed of two sheets of flat glass, each 4.00 mm thick, separated by 5.00 mm of stationary air. If the inside of the window is at 20.0 oC, the external one at -30.0 oC and the cross-sectional area of the window is 6.00 m2, determine for the steady state: kglass= 0,80 W/(m*K); kair= 0,024 W(m*K) a) The temperatures between the air layer ?1 and ?2 indicated in the figure.b) The flow of heat through the window