22 - Which of the following is not one of the functions of resistors in an electrical circuit? A) To act as a freight (buyer). B) To assist the operation of other elements by dividing the supply voltage of the circuit, that is, by reducing it. C) To ensure that circuit elements operating with low current are protected against over current. D) Creating a phase difference between current and voltage

22 - Which of the following is not one of the functions of resistors in an electrical circuit? A) To act as a freight (buyer). B) To assist the operation of other elements by dividing the supply voltage of the circuit, that is, by reducing it. C) To ensure that circuit elements operating with low current are protected against over current. D) Creating a phase difference between current and voltage

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 1RQ: 1. What is the relationship of voltage and current (concerning phase angle) in a pure resistive...

See similar textbooks

Similar questions

Short circuit is occurred when: Select one: a. The voltage between the two terminals is zero although there may be a nonzero current between the terminals. b. All of the given answers. c. There will be a zero-resistance connection between terminal A and B and therefore the 2 terminals are at the same voltage. d. A pair of terminals connected by a wire (of zero resistance).
Figure 1, draw a two-loop circuit where the first voltage in series with first resistor to be connected at the supply side and the second voltage in series with second resistor to be connected at the load side. The three (3) resistors are connected in tee. Label the values of resistors and voltages. Complete the table below.
7 7 - In using Kirchhoff’s rules, you generally assign a separate unknown current to ...... A) each battery in the circuit B) each branch in the circuit C) none of them D) each resistor in the circuit E) each loop in the circuit
An independent current source while providing a fixed current having Select one: a. Unknown voltage across its terminals. b. Not applicable to measure voltage across it. c. Zero voltage across its terminals. d. None of the above.
Topic: Series Resistor and Voltage Division Consider the following two diagrams of series circuits. For each diagram, use arrows to indicate the direction of the conventional current. Then, make comparisons of the voltage and the current at the designated points for each diagram.
a. An electrical engineer was given a contract to design a device with the following specifications: a source voltage of 240 volts and three resistors with 102, 202 and 302 marks on them respectively. This engineer subcontracted this job to you, and instructed you to connect these resistors in series and then in parallel. With your knowledge in circuit analysis; Determine the values of the resistance and the current in each scenario.
2. What is the significance of negative values of voltages and current?
1.Series parallel connection circuit a. Solve for the total value of resistance b. Solve for the value of current given 100Vdc c. Total Power Note: Duplication of the activity will be scored divided by the number of duplication.
What is the Voltage between Outer Wires of the Three wire D.C distribution system. a. three times the Voltage between an Outer and the Neutral Wire O b. two times the Voltage between an Outer and the Neutral Wire O c. half of the Voltage between an Outer and the Neutral O d. same as the Voltage between an Outer and the Neutral Wire
Solve for the voltage, current, and power for all circuit components.
2. In power distribution systems, conductor from which tappings are taken for supply to the consumers is called 3. In circuit breaker, the length of the ARC increases, the resistance will be
-) Please answer the questions below. a) How is the multimeter connected to the circuit for current and voltage measurements? b) Write the color codes of the resistor with 5% tolerance for 33k ohms (for 4 band color coded resistor). c) The colors of the 5-color banded resistor are as follows: Red-White-Black-Red-Red. Calculate the value of this resistor. d) For inductive loads, does the phase difference between current and voltage occur later or behind? Comment e) If it says "104" on a non-polarity concentrator, what is the capacity of the capacitor? f) What parameters does the value of a resistor depend on? Comment.