20k 20k 20k 20k www w 10k output Va 10k 10k 20k (a) Find all the possible output voltages of a weighted resistors D/A converter circuit, if 0 = OV and 1 = 6V. Draw the necessary circuit diagram also. (b) Calculate the full-scale output voltage of a 5-bit binary ladder, if we consider the two logic levels as 1 = 20V and O = OV. (c) Below given is the circuit of binary ladder, with applied digital signals (4-bit). Calculate the analog output voltage at the given input combination, if 0 = OV and 1 = 16V. %3D %3D ww

20k 20k 20k 20k www w 10k output Va 10k 10k 20k (a) Find all the possible output voltages of a weighted resistors D/A converter circuit, if 0 = OV and 1 = 6V. Draw the necessary circuit diagram also. (b) Calculate the full-scale output voltage of a 5-bit binary ladder, if we consider the two logic levels as 1 = 20V and O = OV. (c) Below given is the circuit of binary ladder, with applied digital signals (4-bit). Calculate the analog output voltage at the given input combination, if 0 = OV and 1 = 16V. %3D %3D ww

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Illustrate a 2 bit binary parallel adder (it is a digital circuit that produces arithmetic sum of two binary numbers in parallel) also mark which transistors are “ON” and “OFF” if inputs are 10 and 01 using Emitter-coupled logic (ECL)
Using four MSI circuits, construct a binary parallel adder to add two 16-bit binary numbers. Label all carries between the MSI circuit
Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th R₂ = 5600 R₁ = 4700 M3 Ao M₁ M₂ a. Indicate and verify the state of each MOSFET and V for the following input 0 combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. Example: M1 is assumed to be in saturation. If Vgs = 2 V, Vds = 4V, Vds > Vgs - Vth 4>2-1 4> 1 (ok) Vgs > Vth (2>1) A B M1 state M2 state M3 state V OV OV 5 V OV b. What kind of logic circuit is implemented in the circuit above? 5V www. V₂ 0
Use three MSI circuits,construct a binary parallel adder to add 12 bit binary numbers. Label all carries between the MSI circuit.
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.) 1/6 Pat DigClock Part List OFFTIME = SuS DSTM1 ONTIME = DELAY= STARTVAL = 0 OPPVAL = 1 Sus EUK FleStim AC Lbrajes Design Cache b) Read the specification of 74LS47 (BCD-to-7-Segment Decoder shown in Appendix) to see how the logic IC operates to drive a 7-segment LED display. Draw the circuit connection of the decade counter in (a) and the decoder to display the count value on the 7-segment LED display. Further explain why common anode…
Q1/ To Design 20 – bit BCD adder can using 3(8-bit binary adder), 16 F.A and 8H.A O 2 (4-bit binary adder) , 3 (4-bit binary adder) .10F.A and 2 H.A (8-bit binary adder) , 3 (4-bit binary adder), 10 F.A and 5H.A None of them 2(8-bit binary adder), 1 (4-bit binary adder), 2 F.A and 10H.A
Q1) Design a digital circuit that performs the four logic operations of NAND, NOR, exclusive-OR and exclusive-NOR. Use two selection variables. Show the logic diagram of one typical stage.
Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th W R₂ = 5600 PEETHIPPIN R₁ - 4700 M3 M₁ M. 0 a. Indicate and verify the state of each MOSFET and V for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. 오 Ao SV why
a. Design a 6-bit binary weighted ladder with V₂ = 5 V, R=1 kQ and R, = 5 kQ, a determine i. what will be the Vout if the binary is 101010? ii. what will be the Vout if the binary is 010011?
(a). If I want to store 4-bit data 0110 and at 4th clock I want to extract all the stored bits, which shift register I should explain it with the help of circuit diagram and table. (b). Write comparison between Diode transistor logic and Transistor Transistor logic
1 Design and draw the logic diagram for a two-input NAND gate using one two-input AND and one NOT gate. Include the pin numbers on the gate inputs and outputs.
Draw the logic diagram and transistor implementation for a (2-2-2) AOI.