20.0 mL water sample was titrated with 0.0100 M EDTA solution that required 14.50 mL for CaCO3 hardness. The total hardness of the water sample in terms of CaCO3 (MW = 100.1 g/mole) in parts per million is _________? Note: Express final answer using least number of significant figures.

20.0 mL water sample was titrated with 0.0100 M EDTA solution that required 14.50 mL for CaCO3 hardness. The total hardness of the water sample in terms of CaCO3 (MW = 100.1 g/mole) in parts per million is _________? Note: Express final answer using least number of significant figures.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter5: Errors In Chemical Analyses

Section: Chapter Questions

Problem 5.10QAP

See similar textbooks

Similar questions

Table 8.1 Hardness determination of water samples. Volume of NazHY 2 H20, mL Ca+, mg/L (mean SD) mL of Replicate Sample Initial Final Volume added 54 mL 15.1 15.1 1 54 mL 15.1 30.7 15.6 2 54 mL 30.7 45.3 14.6 3 Sample Calculations (show calculation for one replicate only) mg. (mL of titrantsample) (M of titrant)(40000) Ca2+ mL of sample mg. Ca2+ Biology Environmental Science
1. Straight lime softening A groundwater was analyzed and found to have the following composition (all concentrations are as CaCO): Estimate the lime dose (in mg 1.) required to soften the water. HCO 155mg/1 Ca 210 mg Mg-15mg/1 Alk.-260 ml Temp-10C 2. Excess lime softening A groundwater was analyzed and found to have the following composition (all concentrations are as CaCO)). Estimate the lime dose (in mg/L.) required to soften the water.. H:CO 155mg/1 Ca 180 mg/1 Mg-60mg/1 Alk. -260 mg/1 Temp-10C
Table 2: Absorbance Values of Standards and Unknowns. Sample Blank Standard Solution 1 Standard Solution 2 Standard Solution 3 Standard Solution 4 Standard Solution 5 Water Sample 1 Water Sample 2 Phosphate Concentration (in ppm) Y17 0 ppm 0.02 ppm 0.04 ppm 0.08 ppm 0.16 ppm 0.32 ppm Freeman Lake 0.001 0.325 0.292 0.413 0.315 0.039 0.054 0.049 Absorbance at 2= 690 nm Calculations: 1. Construct a phosphate standard curve in Excel by plotting concentration (in ppm) on your x-axis and Absorbance (unitless) on your y-axis for your known solutions. Label the axes on the graph and provide the curve with a title. Use a linear trendline to generate a best fit line to your data. Label the graph with the equation and the R" value. Insert your labeled graph in the space below. X
C1. A carefully weighed 280mg Calcium carbonate was used in the standardization of an EDTA solution. Initially, 25mL of the titrant was consumed but only after the addition of another 10mL of the titrant did an endpoint was visible. What is the MW of calcium carbonate? (use C1 as reference)* 102 g/mol 98 g/mL 100 g/mL 100 g/mol What is the molar concentration of the standardized EDTA solution? (use C1 as reference)* 0.08m 0.8M 0.08N 0.08M How many grams of EDTA (MW: 292 g/mole) is required to prepare 250mL of a 0.025M solution?* 0.1825 0.1852 1.825 1.1852
100 mL tap water is titrated with 20 mL of 0.02 M EDTA solution to determine the hardness of the water. The second 100 mL tap water is precipitated as CaC2O4 and removed by filtration and the filtrate is titrated with 8.0 mL of the same EDTA solution. What are the concentrations (as ppm) of Ca2+ (40.078 g/mol) and Mg2+ (24.305 g/mol) ions in the water? 2) 10 g of a solution, containing one or more of NaOH, Na3PO4, Na2HPO4, NaH2PO4, H3PO4 and HCl substances, is titrated with 1.0 M NaOH using the phenolphthalein indicator and 34.5 mL NaOH is used. Another 10 g mixture was titrated to reach the bromocresol green end point and 20.50 mL NaOH is used. What is the composition of the solution? What are the percentages of the species(H:1.0078, O:15.99, Na: 22.98, P:30.974, Cl:35.453)?
You took 25.00 mL of unknown water solution and titrated it with EDTA. The EDTA solution molarity was 0.01 M, and it took 16.50 mL to reach the end point. With the blank it took only 0.98 mL to reach end point. 15.52 mL of EDTA solution were used to titrate hardness that actually came from the unknown 1.552×10−4 moles of EDTA reacted with hardness-causing ions from the unknown sample 1.552×10−4 moles of hardness-causing ions were present in the unknown sample A) Assuming that the total hardness of water is due to CaCO3, how many grams CaCO3 does it correspond to? B) What is the total hardness of the unknown water in ppm CaCO3?
Students measured the concentration of HCl in a solution by titrating with different indicators to find the end point. (Use the table to find critical F values.) Mean HCl concentration (M) (+ standard deviation) Indicator Number of measurements 1. Bromothymol blue 0.09565 + 0.00170 28 2. Methyl red 0.08681 ± 0.00098 18 3. Bromocresol green 0.08641 + 0.00106 29 Is the difference between Indicators 1 and 2 significant at the 95% confidence level? O Yes O No Fenlculated clegrees of freedom Ecalculated Is the difference between indicators 2 and 3 significant at the 95% confidence level? O Yes O No Fealculated Spooled tcalculated
A. Calculate the solubility of PbI2 (Ksp = 1.5 x 10-8) in moles per liter. Ignore any acid–base properties. B. Calculate the solubility of CdCO3 (Ksp = 5.1 x 10-12) in moles per liter. Ignore any acid–base properties. C. Calculate the solubility of Sr3(PO4)2 (Ksp = 1.5 x 10-31) in moles per liter. Ignore any acid–base properties.
2. 100 mL tap water is titrated with 20 mL of 0.02 M EDTA solution to determine the hardness of the water. The second 100 mL tap water is precipitated as CaC204 and removed by filtration and the filtrate is titrated with 8.0 mL of the same EDTA solution. What are the concentrations (as ppm) of Ca²* (40.078 g/mol) and Mg* (24.305 g/mol) ions in the water?
A 0.9092g sample of wheat flour was analyzed by Kjeldahl method. The ammonia formed was distilled into 50.00 mL of 0.05063 M HCl; a 7.46 mL back titration with 0.04917 M NaOH was required. Calculate the % protein in the flour. Input the value only. Express in 2 SF.
Concentration sodium thiosulfate solution used: 0.056 mol L-1 ACCURATE TITRATION VOLUME OF SODIUM THIOSULFATE SOLUTION USED Volume titration 1, (ml) Volume titration 2, (ml) Your Group 15.80 15.75 Group 1 16.05 15.70 Group 2 16.30 16.25 ANALYSIS Average volume used, (mL) Standard deviation Number of moles sodium thiosulfate used, (mol) Number of moles calcium iodate in solution, (mol) Volume of calcium iodate used, (mL) Concentration of saturated calcium iodate solution (mol L-¹) Unrounded value 15.9750 0.26220 Rounded value 15.97 0.262 10.0
Concentration sodium thiosulfate solution used: 0.056 mol L-1 ACCURATE TITRATION VOLUME OF SODIUM THIOSULFATE SOLUTION USED Volume titration 1, (mL) Volume titration 2, (mL) Your Group 15.80 15.75 Group 1 16.05 15.70 Group 2 16.30 16.25 ANALYSIS Average volume used, (ml) Standard deviation Number of moles sodium thiosulfate used, (mol) Number of moles calcium iodate in solution, (mol) Volume of calcium iodate used, (mL) Concentration of saturated calcium iodate solution (mol L-¹) Unrounded value 15.9750 0.26220 0.00089400 0.00036700 A Rounded value 15.97 0.262 8.94 x 10-4 10.0 Minimize