20. Spring Theory. One end of a spring with spring constant k = 6.50N /m is connected to a ball of mass m = 5.00kg while the other end is attached to a ceiling. The ball is initially held in place such that the spring is at its natural length of Lo = 7.00m and at an angle of = 125 deg with respect to the vertical. Once the ball is released from rest, the system undergoes damped oscillation. Find the length L of the spring a very long time after the ball was released. Lo, m

20. Spring Theory. One end of a spring with spring constant k = 6.50N /m is connected to a ball of mass m = 5.00kg while the other end is attached to a ceiling. The ball is initially held in place such that the spring is at its natural length of Lo = 7.00m and at an angle of = 125 deg with respect to the vertical. Once the ball is released from rest, the system undergoes damped oscillation. Find the length L of the spring a very long time after the ball was released. Lo, m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A mass-spring system exhibits a period of 5 s and a measured mass of 20 kg. Calculate the spring stiffness k.
Clear selectior A mass-spring system oscillates on a frictionless horizontal surface in simple harmonic motion with an amplitude A = 0.1 m. At what position (x = ?) would the kinetic energy of the system be equal to three times its elastic potential energy (K = 3U)? %3D At x = +0.05 m At x = +0.04 m At x = +0.025 m At x = +0.08m At x = +0.1 m A traveling wave on a taut
A factory in Liverpool only have available springs in stiffness values of 10, 100, and 1000 N/m. Design a spring system using these values only, so that a 100-kg mass is connected to ground with frequency of about 1.5 rad/s.
B-increase of spring coefficient like 0.5 k, 2k, 5k and / orhow does the natural frequency of the system decreasereferencesexternal links
1. Figure 1 shows a rocking mechanism that consists of two masses m₁ and m₂ connected by a rigid and massless rod, which is pivoted with two unequal arms of lengths a and b. The lower mass m₁ is laterally supported by a viscous damper with damping coefficient c, while the upper mass m₂ is by a linear spring with spring constant k. The damper and the spring are undeformed when the rod is vertical. The rocking angle from the vertical is 0 (t) and the horizontal displacement of the upper mass is r(t). A moment Mo(t) is applied to the rod at the pivot. The rocking mechanism is in the vertical plan and g is the gravitational acceleration. Derive the equation of motion governing (t) of the rocking mechanism in Fig. 1. Assume that the motion is small, i.e., 0(t) < 1, so that the spring and damper remain horizontal during the motion. Under the small-motion assumption, how is r(t) related to 0(t)? C m₂ الشيخ m₂ Mo(t) Figure 1: A rocking mechanism with two unequal arms
Consider a spring-mass system with mass equal to 1 kg, spring constant equal to 25 Newton/meter.Which damping constant b causes critical damping?If the damping constant b in the above system is set to 3 N ∙ sec/m, then what can be said about the number of timesdoes the object pass through its equilibrium position?If the damping constant b in the above system is set to 8 N ∙ sec/m, then what is the interval of time between thesecond time the object returns to its equilibrium position and the third time it returns to its equilibrium position?
5. Consider modeling the vertical suspension system of a small sports car as a single degree of freedom system of the form: mx + cx' + kx = 0 where m is the mass of the car and c and k are the equivalent damping and stiffness of the four-shock-absorber-spring systems. The car deflects the suspension system 0.05 m under its own weight. The suspension is designed to have a damping ratio of 0.3. a) Calculate the suspension system's equivalent damping and stiffness coefficients, if the car has a mass of 1500 kg. Also, determine the natural frequency. b) Then, with the same suspension, if two passengers, a full gas tank, and luggage totaling 350 kg are loaded in the car, determine the natural frequency and damping ratio. c) Comparatively discuss the results provided in parts (a) and (b) in terms of damping capacity, natural frequency, the amplitude of vibration, and time duration for vibration to nearly stop.
Question 1. A body of mass 100 kKg is suspended by a spring of stifness of 30KN/m and a dashpot of damping constant 1000 N.s/m. Vibration is excited by harmonic force ft)=80 cos (67tt) 1- Write the equation of motion of the system using Lagrange's equation. 2- Find the natural frequency and the driving frequency. 3- Write the complete solution of the vibrating system.
Consider the two-degrees-of-freedom mass-spring system below. Assume m₁ = 30 kg, m2 = 35 kg. If the second natural frequency of the system is 100 rad/s, the value of stiffness k is www. k₁=k k₂ = k k3= k 174.41 kN/m 107.38 kN/m 140.93 kN/m 39.24 kN/m 73.62 kN/m Next 000 00 Previous 4 x₁ (t) x₂ (t) m₁ m₂. mm
A 0.600kg mass oscillates at the end of spring that has a spring constant of 300N/m. the initial amplitude is 0.500m . the damping force is proportional to the velocity, -av. If the amplitude decreases from .50m to 350m in 2.50s . What is the damping constant ?Is the system underdamped, critically damped or overdamped?
Q1. The cantilever beam shown in Fig.1 has an end of mass = 10 kg. The response of the system is x₁ = 0.5 m, x2 = 0.25 m and damping time = 3 sec. Find out the equivalent stiffness and damping of the beam. (Note: Assume that the beam is massless). Ä m Fig.1: Cantilever beam.
An electric motor of mass 25 kg is supported on a three-spring system. Thesprings are arranged in parallel, with the three stiffnesses being 10 kN/m,5 kN/m and 25 kN/m respectively. Viscous damping is present within the systemand has a magnitude of 0.4 kNs/m.i) Produce a sketch of the system and state its equation of motion.ii) Determine the damping ratio and comment on its value.iii) Determine the amplitude of vibration of the motor 5 cycles afterit is released from an initial displacement of 15 mm.