20. At inlet to a certain nozzle, the specific enthalpy of the fluid passing is 3000 kl/kg and the velocity is 60 m/sec. At the discharge, the specific enthalpy is 2762 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (a) find the velocity at exit from the nozzle (b) if the inlet area is 0.1 m' and specific volume at inlet is 0.187 m/kg, find the mass flow rate (c) if the specific volume at the nozzle exit is 0.498 m/kg, find the exit area of the nozzle.

20. At inlet to a certain nozzle, the specific enthalpy of the fluid passing is 3000 kl/kg and the velocity is 60 m/sec. At the discharge, the specific enthalpy is 2762 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (a) find the velocity at exit from the nozzle (b) if the inlet area is 0.1 m' and specific volume at inlet is 0.187 m/kg, find the mass flow rate (c) if the specific volume at the nozzle exit is 0.498 m/kg, find the exit area of the nozzle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 KJKG. In addition, the velocity is 50 ms. At the discharge end, the enthalpy is 2600 kJAg. The nozzle is horizontal and there is negligible heat loss from it. a. Find the velocity at the exit of the nozzle? b. If the inlet area is 900 cm² and specific vohme at the inlet is 0.187 m'kg, find the mass flowrate? c. If the specific volume at the exit of the nozzle is 0.498 m'/kg, find the exit area of nozzle? Fhuid in Fhaid out V2= ? A2= ? V- 50 m/s A- 900 cm? hi- 2800 kJkg h2= 2600 kJ/kg
At inlet to a certain nozzle the specific enthalpy of the fluid passing 3500 kJ/kg and the velocity is 70 m/sec. At the discharge the specific enthalpy is 2782 kJ/kg. The the nozzle is Horizontal and there is negligible heat loss from it. (a) find the velocity at exit from the nozzle (b) if the inlet area is 0.1 m^2 and specific volume at inlet is 0.198 m^3/kg, find the mass flow rate (c) if the specific volume at the nozzle exit is 0.598 m^3/kg, find the exit area of the nozzle
At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 kJ/kg. In addition, the velocity is 50 m/s. At the discharge end, the enthalpy is 2600 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. a. Find the velocity at the exit of the nozzle? b. If the inlet area is 900 cm? and specific volume at the inlet is 0.187 m/kg, find the mass flowrate? c. If the specific volume at the exit of the nozzle is 0.498 m/kg, find the exit area of nozzle? Fluid in + Fluid out V2 = ? V = 50 m/s A= 900 cm? hi = 2800 kJ/kg A2= ? h2 = 2600 kJ/kg
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
Please show your complete solution. Thank you! Air flows in a steady flow manner through a converging tube. At the inlet the pressure is 690kPaabs and the density is 0.838 kg/cu.m. If air enters with a volume flow of 125 cu.m per min at the rate of 94 m/min and the exit section has a diameter of 350mm, determine a.) the mass flow rate, kg/min b.) the diameter of the entrance section and c.) the exit velocity. Assume that the density is constant.
5. Two gaseous streams enter a combining tube and leave as a single mixture. These apply at the entrance section. Find the speed at section 2, the flow rate and area at section 3. data A1 = 75 in?, V1 = 500 fps, vị = 10 ft³/lb At exit: V3 = 350 fps, v3 = 7 ft³/lb ;A2 = 50 in?, ṁ2 = 16.67 Ib/s, p2 = 0.12 Ib/ft³
The air in a car tire is held at a pressure of 220 kPa (gage) in an atmosphere where the atmospheric pressure is 94 kPa. The air inside the tire is at an ambient temperature of 25 degrees Celsius. now accidentally there was a 4 mm air leaking hole in the tire. Assuming isotropic flow, find the mass flow rate of the air passing through the hole.
Disregard the velocity at the entrance
Q4) The nozzles receive steam at 1.75 MPa, 300 °C, and exit pressure of steam is 1.05 MPa. If there are 16 nozzles, find the cross-sectional area of the exit of each nozzle for a total discharge to be 280 kg/min. Assume nozzle efficiency of 90%. If the steam has velocity of 120 m/s at the entry to the nozzles, by how much would the discharge be increased?
H.w : nitrogen gas flows into a convergent nozzle at 200 kpa 400 K and very low velocity it flows out of the nozzle at 100 kpa 330 Kif the nozzle is insulated find the exit velocity C, for nitrogen =1.042
Two gases enter a combining tube and leave as a single mixture. . For the first gas, A₁=72in² V₁=205m/s V₁=120gal/lbm . For the other gas, A₂=48in² m2=20lbm/s P2=2kgm/m³ ● . At the exit, V3=320ft/s V2=9ft³/lbm Find the (a) velocity at section 2 in m/s, (b) mass flow rate at the exit section in kgm/s, and (c) area at the exit section in m².
A water truck drives slowly around a construction site, spraying water to keep dust down. A pump maintains a constant pressure of 100 kPa, gage, and the water is dispersed through 20 spray nozzles, each of diameter 0.01 m. If the truck is initially filled with 4000 L of water, and the flow rate is constant, determine how long the truck can drive before a refill is necessary in seconds.