2.A boom AB is supported in a horizontal position by a hinge A and a cable which runs from C over a small pulley at D as shown in the figure. Compute the tension T in the cable and the horizontal and vertical components of the reaction at A. Neglect the size of pulley at D. T 8' C A 3' 3' 3' 100lb 200 lb

2.A boom AB is supported in a horizontal position by a hinge A and a cable which runs from C over a small pulley at D as shown in the figure. Compute the tension T in the cable and the horizontal and vertical components of the reaction at A. Neglect the size of pulley at D. T 8' C A 3' 3' 3' 100lb 200 lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Similar questions

The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
In Sample Problem 5.5, compute the tension TAD using one scalar equilibrium equation.
Compute the tension TAE in Sample Problem 5.7 using one scalar equilibrium equation.
Find the internal force system acting on section 3 for the pin-connected frame.
Select the distance a between 2 m and 5 m and the force P between 15 kN and 35 kN in the cage system shown in the figure and find the rod forces. Also note that the forces on the rods did not compress my tension. (AE, AB, BE, DE, CD, BC, BD =?)
The rigid body is supported by a hinge at A and a cable at C. The hinge resists 5.5m translation in all three coordinate directions and rotation in the x and y directions. The 260 N force is in the -x direction and acts at the center of the 3m body. Find the tension in the cable and the components of the support C 2.5m 260N reactions at A. Your answer should include a properly Ilm annotated FBD. B 3.Im
The cylinder C in the figure below weighs 1000lbs. Determine the tension in the cable , and the reactions A and F
The dual-grip clamp shown in the figure is used to provide added clamping force with a positive action. If the vertical screw is tightened to produce a clamping force of 3.7 kN and then the horizontal screw is tightened until the force in the screw at A is doubled, find the total reaction R on the pin at B.
H CABLES & RODS 100° HORIZONTAL 45° E 90° F 115° 1. The block system is stationary as shown in the figure. Compute В 55° 85° the internal reaction of the horizontal cable 145° LA GI. 10 KN 20 KN 20 KN 40 KN
The boom ABC in Fig 4 is held by the ball and socket joint at A and the two cables EBF and CD, as shown. The cable EBF passes through a frictionless pulley at B. A 20 kN force acts as shown at point C. Calculate the tensions in the two cables and the reactions at A. Neglect the weight of the boom. 2 m E. B 1 m 20 kN Im 1.5 m- 1.5m
Find the tension in string A and the force B exerted on the string by the beam in the figure.
A 400 N gas sign hangs from the end of a uniform strut BC. The strut is 4 m long and weighs 600 N. The strut is supported by a hinge at the wall at C and by a cable whose other end is tied to the wall at point A 3.0 m above the left end of the strut. Find the tension in the supporting cable and the force of the hinge on the strut. 5.0 m 3.0 m 4.0 m B GAS TAB= 1333 N TAB= 1167 N TAB= 400 N TAB= 1000 N leave the question 4 Other: Q 4 4 points Rc= 980 N O Rc= 360 N Rc= 890 N Rc= 1085 N O O O O O O O