2.5) For a conventional amplitude modulation system, the modulated signal is given as, s(t)=[4, +m(t)]cos(27f!) If the message signal is given as, m(t)=cos(200zt)+ cos(600zt) and the power efficiency is 7=0,63 a) Find the modulation index, µ. b) Find and plot the spectrum of modulated signal, s(t).

2.5) For a conventional amplitude modulation system, the modulated signal is given as, s(t)=[4, +m(t)]cos(27f!) If the message signal is given as, m(t)=cos(200zt)+ cos(600zt) and the power efficiency is 7=0,63 a) Find the modulation index, µ. b) Find and plot the spectrum of modulated signal, s(t).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

:A modulating signal is used to modulate a carrier signal(AM modulation). Let Pr , Pc, PSB, PUSB, PLSB and u are the total power, side band power, upper side band power, lower side band power and modulation index respectively. power, carrier Prove the following: a. Pc = Pr (me) m2 b. PSB = Pr m2 PLSB = 72+m2, c. PUSB = Pr 2+m2
Plot an AM modulated signal , that has an information signal m ( t ) = 10 sin ( 10nt ) and a carrier signal c ( t ) = 15 cos ( 1000nt ) . Calculate the modulation index ( u ) . Is it a good modulation ? If no , suggest a change in one of the signals above and calculate u again , so that it approaches ideal case
Q2: A modulating signal is used to modulate a carrier signal(AM modulation). Let Pr , Pc, Psa. PusB, PLSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively. Prove the following: a. Pc = Pr () c. Pusp = Pasa =) P, 2+m2. b. PsB = Pr %3D 2+m2 2 (2+m2
zain IQ AM Modulatio... -> AM Modulation 1. What is the main feature in AM modulation, that is used to judge if the modulation is good or not? Explain with examples. 2. Can AM modulated signal change phase and/or frequency? Explain the reason. 3. What is modulation index? Its formula? 4. Plot an AM modulated signal, that has an information signal m(t) = 10 sin(10nt) and a carrier signal c(t) = 15 cos(1000t). Calculate the modulation index (u). Is it a good modulation? If no, suggest a change in one of the signals above and calculate u again, so that it approaches ideal case. 5. Draw the modulation block diagram of AM. ...
An FM signal has a maximum frequency deviation of 1500h and a modulating frequency of 500h, its total power is 6500w, applied to a resistive load of 1ohm, the carrier frequency is 400Mhz. Determine the voltage of the modulated signal and the modulation voltage.
If Va = -3sin[2pi(2x103)t] and Vb = -10cos[2pi(200x103)t] 1. Write the equation of the AM signal 2. Calculate the percent modulation 3. Sketch the AM wave
A carrier wave of 30 V amplitude and 6 KHz frequency is modulated by an information signal m(t)=4sin(200t)-6cos(400t). Write the modulated signal spectrum.
2 (AM) A 10 V amplitude sinusoidal signal is used as a modulating signal to generate an AM signal with modulation index 0.8. What is the amplitude of the carrier? What is the power of the side bands? What is the efficiency of the modulated signal?
Discussion: 1. Find the instantaneous frequency of the following waveforms: s, (t) = A.cos (100nt + sin20nt) S2(t) = Accos [100nt +nt?) 22 |Page Communication Lab by Asst. Lecture Zahraa K. 2. A 500 Hz modulating voltage produces a frequency deviation of 2.25 kHz. What is the modulation index ? If the amplitude of the modulation voltage is kept constant, but its frequency is raised to 6 kHz, what is the new deviation ? 3. When the modulating frequency in an FM system is 400 Hz and the modulation voltage is 2.4V, the modulation index is 60. Calculate the maximum deviation. What is the modulation index when the modulating frequency is reduced to 250 Hz and the modulating voltage is simultaneously raised to 3.2V ?
A 1500 KHz carrier with amplitude of 50 V is amplitude modulated by 2 –KHz sine wave tone with a peak voltage of 15 V. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
Q 2 : An audio signal given by 15 sin( 000 pi t)+20 sin(8000 pi t) amplitude modulated DSB-FC) a sinusoidal carrier wave 60 sin(100,000 ) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why? Q 2 : A modulating signal is used to modulate a carrier signal(AM modulation). Let P T . P c ,P SB . P USB , P LSB and u are the total power, carrier power, side band power, upper side band power, lower side band power and modulation index respectively, Prove the following: a. P c =P T ( 2 2+m^ 2 ) b. P SB =P T ( m^ 2 2+m^ 2 ) c. P USB =P LSB = 1 2 ( m^ 2 2+m^ 2 )P T
:Q2 „Draw the waveform of AM wave for the following values of modulation index, assuming the information and carrier signals to be sinusoidal signals a) O b)0.5 c) 1 d) 1.5