2.30 m long and has a mass m = 15.0 kg. It leans at rest against a smooth wall making an angle 0 = 29.0° with the wall as shown on the left. The coefficient of static friction between the floor and the ladder is u, = 0.675, while the coefficient of kinetic friction is u, = 0.439. What is the 2. A ladder is L force between the wall and the ladder? Hsi Hk

2.30 m long and has a mass m = 15.0 kg. It leans at rest against a smooth wall making an angle 0 = 29.0° with the wall as shown on the left. The coefficient of static friction between the floor and the ladder is u, = 0.675, while the coefficient of kinetic friction is u, = 0.439. What is the 2. A ladder is L force between the wall and the ladder? Hsi Hk

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The forces are in static equilibrium. The 140 lb force is directed along the x-axis and the 300 lb force is directed along the negative z- axis. Determine the magnitude of the unknown force, R. Z X R Ox лог 140lb A (-50, 80, 160) lb By 300 lb у
The 6-m pole ABC is acted upon by a 460-N force, P, as shown in the figure. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. For a = 3 m, determine the tension in each cable and the reaction at A. (Round the final answers to one decimal place.) 3. 1.5 m P E The tension in cable BD is The tension in cable BE is The reaction at A is - ( y C B 3 m N. N. N)i + 3 m 3 m 1.5 m 3 m X N)j + N)k.
A cable weighing 4 kg/m is supported at the ends by two towers of the same height 100m apart. a. Flnd the sag at the center if the cable is 128.16m long. b. Find the tension at the lowest point of the cable. c. Find the tension at the highest point of the cable. A) a. 45.54m ; b. 610kg; c. 203kg B a. 35.54m ; b. 302.16kg ; c. 160kg c) a. 45.54m ; b. 160kg ; c. 203kg a. 44.45m ; b. 610kg ; c. 602.36kg E a. 53.54m ; b. 302.16kg ; c. 160kg
16. ao The drawing shows a rectangular piece of wood. The forces applied to corners B and D have the same magnitude of 12 N and are directed parallel to the long and short sides of the rectangle. The long side of the rectangle is twice as long as the short side. An axis of ro- tation is shown perpendicular to the plane of the rectangle at its center. A third force (not shown in the drawing) is applied to cor- ner A, directed along the short side of the rectangle (either toward B or away from B), such that the piece of wood is at equilib- rium. Find the magnitude and direction of the force applied to corner A. A D Axis Problem 16
I 00LLJ408 - Go.. Question Info and Solutions Blocks A and B of mass 5 kg and 10 kg respectively are placed on a Smooth inclined plane of Inclination 30, as shown. Block A and B are subjected to forces 5 N And 50 N respectively along the incline, as shown. The coefficient of friction between A andBis 0.50 find the frictional force between A and B in N is: (g= 10 ms SOH 300 Options Solution Fs=Static frictional force umg cos 30 (0.5) (5) (10) cos 30 21.6 N Let a be the acceleration of both the blocks along 5.27 PM
This problem concerns the concept of tension in a rope. Consider a rope subjected to a pulling force on its two ends as shown in (Figure 1). The rope is stationary. An arbitrary point P divides the rope into a left-hand segment L and a right-hand segment R. Figure wi L pull R 232 pull 1 of 3 Part A For segment R and segment L to hold together, they must exert forces on each other. What is the direction of the force exerted on segment R by segment L? View Available Hint(s) left right Submit Part B FLR Assume that segment R exerts a force of magnitude T' on segment L. What is the magnitude FLR of the force exerted on segment R by segment L? Give your answer in terms of T and other constants such as g. ► View Available Hint(s) = Submit % ΑΣΦ www ?
A 60.0 cm, uniform, 50.0 Nshelf is supported horizontally by twov verticalwires attached to the slopingc ceiling(Fig. ). A very small 25.0 N tool is placed on the shelf midway between the points where the wires are attached to it. Find the tension in each wire. Begin by making a free-body diagram of the shelf.
A skier is standing on a 30o hill. Draw the hill and add idealized force vectors that represent the force of the skier (FS), the normal force (FN), and the force of friction (FF).
A 80-kg block is suspended as shown. The beam is weightless and is hinged to the wall at A. The tension force of the cable T has magnitude: (Use g = 9.8 m/s2) %3D T. 3m A 4m block O a 980 N Ob. 817 N Oc. 1143 N Od. 620N O e. 1307 N
The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant Rat A. The couple is positive if counterclockwise, negative if clockwise. 2.19 KN 0.65 m 1.74 m. 75° A Answers: M = i R=( i y 550 N.m kN.m i+ i 0.16 m 0.16 m 1.17 KN j) kN
a person is trying to judge whether a picture (mass =2.59kg) is properly positioned by temporarily pressing it against a wall. the pressing force is perpendicular to the wall. the coefficient of static friction between the picture and the wall is 0.650. What is the minimum amount of pressiong force that must be used? answe is 39N
A manual roller of weight mg = 337.5 N is pushed with a force 182.8N at an angle 0, such that sin(e) = 0.4, with the horizontal direction. What is the force exerted by the floor on the box? F cose F sine mg