[2.26] The length of 2 mm diameter steel wire CD has been adjusted so that with no load is applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. Knowing that E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. 0.25 m 20 kg В A E |1.5 mm 0.32 m 0.08 m

[2.26] The length of 2 mm diameter steel wire CD has been adjusted so that with no load is applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. Knowing that E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. 0.25 m 20 kg В A E |1.5 mm 0.32 m 0.08 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The steel stepped rod carries the axial loads shown in Fig. Knowing that Aj=20 cm², A2=10 cm², E=200 GPa, [G]=160Mpa. Odraw the diagram of the axial force of the rod. check the strength of the rod. Odetermine the change in the length of the rod. - A1=20cm? A=10 cm 160KN 40KN 200KN B 400mm 400mm
Q2. A rigid bar AB is supported by a hinge at A and by a steel wire T as shown. With no load applied on the bar, the end B is 2 mm above the contact point C. Determine where a W=390 N load should be placed on the bar so that the end B will just touch the support at C. For the steel wire E=200 GPa. STEEL WIRE D=2.50 mm 300 mm T. E=200 GPa 2 mm A 100 mm 400 mm
Two rods, A and B. of equal free length are elastic. Both hang vertically 0.6m apart and support a rigid bar horizontally. The bar remains horizontal when a vertical load of 60 KN is applied to the bar 0.2m from A. If the stress in A is 100 MPa, determine the stress in B and the cross-sectional areas of the two rods: Ea = 200 GPa, EB = 130 GPa.
As shown on the right, two circular rods (CE and DF) are attached to a rigid bar (ABCD). Knowing that 2 m 1m 3 m the diameters of the rods are: der = 10 cm dor = 20 cm the young's moduli of the rods are ECE = 200 GPa Epr = 80 GPa 4 m 5 m 10KN Determine the forces applied by the two rods, i.e., Fce and For
EXERCISE PROBLEMS 1. Draw the FBD of member 4. Draw the FBD of member ABC ADB 160 mm 90 mm 240 N 20 lb 180 mm - 15 in. 15 in.→- 15 in.- B A M В 320 mm D 125 mm D - 300 mm- 5. Draw the FDBS of member ADB and BEC 1 m 2. Draw the FBD of the entire structure 1 m 2 m В 18 kN E D 1 m 2 m B D E 2 m 1.6 m AO F A -3.6 m- 3. Draw the FBDS of all members -3.6 m- A 2.7 m | 2400 N B D 2.7 m 1.5 m E° F 4.8 m
3. The gap between the shaft and the wall initially is 2 mm. After the loads applied, the body deforms and reaches to the wall on right. Determine the support reactions at two sides A and C when the loads are applied. The shaft assembly is made of material with modulus of elasticity of 200MPA A C 2mm B 100kN 150KN 15cm 5cm 35cm 45cm (Answer: F. = 133.2kN, F = 116.8kN )
= A system of three steel (E = 30, 000 ksi) pipes is loaded and supported as shown below. The loads are applied to the rigid plates that connect the pipes at B, C, and D. Determine the change in length of the complete system of pipes if the cross-sectional areas of pipes AB, BC, and CD are 1.2 in², 1.0 in², and 0.8 in², respectively. A 14 in B 16 in -30 kip с 20 in 5 kip D 15 kip
2. The length of the 2-mm-diameter steel wire CD has been adjusted so that, with no load applied, a gap of 1.5 mm exists between the end Bof the rigid beam ACB and a contact point E. load should be applied to the beam to cause contact between B and E. Using E = 200 GPa, determine where a 225-N 250 mm 225 N 1.5 mm B C A 360 mm 90 mm
A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of 200 MPa. The rod is 250 mm long and one part of its length is square and the remainder is circular with a diameter of 25 mm. If the total strain energy in the rod and modulus elasticity of the material is 1.3 J and 200 GPa, determine the following:1.The applied load F2.The total extension of the bar3.The length of the square portion of the bar4.The suddenly applied load that will induce the same amount of energy 5.The load that falls from a height of 8 mm induces 1,3 J in the bar.
Two cylindrical rods, one of steel and the other of brass, are joined at C and Q1) restrained by rigid support at 4. There is a gap of 1 mm between end E and rigid support at right side. For the loading shown and knowing that E; = 200 GPa, E = 105 GPa, as = 13×106 1/°C and as = 19×10-6 1/°C, determine the minimum change in temperature to close the gap. Dimensions in mm 100 100 F180- 120- A D Brass Steel Be 60 kN 40 kN 20-mm diam. 10-mm diam.
The 1021-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 472 mm2. Find the magnitude of P (in N) that can be safely applied to the bar if the stresses in AC and BD are limited to 110 MPa and 51 MPa, respectively. Express your answer in two decimal places.
A 1.05-m-long rod of negligible weight is supported at its ends by wires A and B of equal length. The cross-sectional area of A is 1.80 mm^2 and that of B is 4.20 mm^2 . Young's modulus for wire A is 2.30×1011 Pa ; that for B is 1.20×1011 Pa . At what point along the rod should a weight w be suspended to produce equal stresses in A and B? (d=? m from wire A) At what point along the rod should a weight w be suspended to produce equal strains in A and B? (d=? m from wire A)