4 decimal places 2. Plastic kayaksare manufactured using a process called rotomolding. Moltenplastic is injected into a mol, which is then spun on the long axis of theKayak until the plastic cools, resulting in a hollow one-piece craft. Supporethat the induction motors used to spin the molds consume Ju kW ata PF220LO Vrms, 60Hz line. DetermineOF0.88 lagging from athe (a) capacitor bank to be placed in parallel with the load to increasePF to 0.98 lagging. What is the new reactivethe?power

Answered: Image /qna-images/answer/e9620b18-388c-4802-a754-d58ff4f2df08.jpg

2. Plastic kayaks are manufactured using a process called rotomolding. Molten plastic is injected into a mol, which is then spun on the long axis of the Kayak until the plastic cools, resulting in a hollow one-piece craft. Suppare that the induction motors used to spin the molds consume Ju kW at a PF of 0.88 lagging from a 220LO° Vrms, Gotz line. Determine the (a) capacitor bank to be placed in parallel with the load to increase ? the pF to 0.98 lagging. What is the new reactive power

2. Plastic kayaks are manufactured using a process called rotomolding. Molten plastic is injected into a mol, which is then spun on the long axis of the Kayak until the plastic cools, resulting in a hollow one-piece craft. Suppare that the induction motors used to spin the molds consume Ju kW at a PF of 0.88 lagging from a 220LO° Vrms, Gotz line. Determine the (a) capacitor bank to be placed in parallel with the load to increase ? the pF to 0.98 lagging. What is the new reactive power

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

7- An 8-pole d.c. machine of 1200kW, 600V, 500 rpm and the average value of the reactance voltage per coil is 6.6v. the machine is lap connected of 648 conductor and each coil has two turns, the axial length of the compole 29 cm and the air gap is 0.8 cm, the armature diameter is 0.35m and the ratio (Bmax/Bav) = 1.5. Find the interpole m.m.f. %3D
Match the following A cathode Choose... electrodynamometer instrument Choose... In single phase energy meter, is placed at the edge of Aluminum disc, which controls the speed of the disc. O series magnet O brake magnet O shunt magnet O M type magnet
Q25) i) What are the factors that the induced voltage in three phase induction motor depends upon and Explain how the rotating magnetic field is produced in the three phase induction motor.
A 6-pole generatro has 600 conductors. If the flux per pole is 20mWb, at what speed must the armature be drive to generate 240V if a) lap wound connection, or b) wave wound connection.
A toroid (ring shaped) magnetic core is wounded by a coil having 250 turns. The inner (ri) and outer radii (rd) are 20cm and 25cm, respectively. The toroidal core has a circular cross section (S). For a coil current of 2.54 A, calculatea. The magnetic flux density along the mean radius of the core (l).b. Flux in the core.c. Flux linkage of the coil.d. Reluctance of the toroid core.e. Magnetic permeability of the material.f. The inductance of the coil, under the assumption that the flux density within the core is uniform and same at every point of the core.H
The machine shown in Figure 2 has three concentrated stator coils, each of eight turns. The coils are arranged symmetrically around the stator at120° intervals. The poles of the rotor are so shaped that the air-gap flux density due to the rotor mmf is nearly sinusoidally distributed. The total rotor flux is 0.040 Wb. The rotor is driven at 3000 r/min. (a) Determine the frequency of the voltages generated in the coils. (b) If the stator terminals a', b' and c' are connected to form a Neutral point o, find the rms voltage between any two of the terminals a, b,and c. Figure 2 SO 6.
In spintronics, information is stored and transmitted using the 'Charge' property of electrons. True False
A toroid (ring shaped) magnetic core is wounded by a coil having 250 turns. The inner (ri) and outer radii (rd) are 20cm and 25cm, respectively. The toroidal core has a circular cross section (S). For a coil current of 2.54 A, calculatea. The magnetic flux density along the mean radius of the core (l).b. Flux in the core.c. Flux linkage of the coil.d. Reluctance of the toroid core.e. Magnetic permeability of the material.f. The inductance of the coil, under the assumption that the flux density within the core is uniform and same at every point of the core.
2nd - What does induction loading mean? a) friction load B) load with effect NS) loading by contact D) charge by electric field TO) charge with magnetic field
HAWT type wind turbine has the following data, height of tower =100 m, diameter of rotor = 80 m, determine the power extracted by the turbine, if the wind speed at this height is 15 m/s, and reduced by 20 %, suppose the air density is 1.3 kg/m3. * Pm = = 2.6 MW. Pm = = 3.6 MW. Pm = = 4.6 MW. Pm = = 5.6 MW.
The torque angle of synchronous machine operating from a constant voltage bus, is usually defined as the space angle between rotor mmf wave and resultant flux-density wave O True O False
The Cathode Ray Oscilloscope (CRO) may be used in the observation of waveforms to do the measurements of voltage, current, phase and periodic time. Due to increased armature m.m.f, the armature reaction during load condition will decrease and hence the field flux will be increased. Select one: O True O False