2. Locate the centroid (x, y) of the metal cross section. Neglect the thickness of the material and slight bends at the corners. (Hints: Consider symmetry. Use line segments. You may treat the upper circular section as one uniform half circle. Ignore the length of the arches.) 50 mm. 50 mm 100 mm 100 mm 50 mm plz show all the work 150 mm

2. Locate the centroid (x, y) of the metal cross section. Neglect the thickness of the material and slight bends at the corners. (Hints: Consider symmetry. Use line segments. You may treat the upper circular section as one uniform half circle. Ignore the length of the arches.) 50 mm. 50 mm 100 mm 100 mm 50 mm plz show all the work 150 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55 mm, S' = 60 mm, Az1 = 5 mm, and A₂ = 8 mm. Side D'B' remains horizontal. Figure 91.5 ATL Ax₂ 1 of 1
Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid coordinates (X , ỹ) relative to the axes origin, 0. The dimensions for the section in Figure Q2b are b1 = 15.75 mm , b2 = 15.75 mm, b3 = 62.50 mm, d1 = 75.85 mm and d2 = 20.25 mm. Calculate the second moment of area for the solid and homogeneous section shown in Figure Q2b about its centroidal x-axis. Give your answer to two decimal places. y b1 b2 di d2 b3
Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid coordinates (x̄ , ȳ) relative to the axes origin, O. The dimensions for the section in Figure Q2b are b1 = 15.75 mm , b2 = 15.75 mm, b3 = 62.50 mm, d1 = 75.85 mm and d2 = 20.25 mm. Calculate the second moment of area for the solid and homogeneous section shown in Figure Q2b about its centroidal x-axis. Give your answer to two decimal places.
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive load of 250 kN. The section dimensions are breadth, b= 0.12 m, depth, d= 0.05 m with an equal thickness on all sides, t= 0.003 m. Calculate the compressive stress ơ in the tube. Give your answer in N/mm² to 2 decimal places. Figure Q2a Rectangular Tube Section Question 2 continues on the next page.
3) A right circular cone of 30 mm diameter and 60 mm height is cut from a cylinder of 50 mm diameter and 120 mm height as shown in the figure. Find the position of the CG of the body from its base. 50 Ans CG of the given section is at (0mm, 62.87mm,0mm)
Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive load of 250 kN. The section dimensions are breadth, b 0.12 m, depth, d = 0.05 m with an equal thickness on all sides, t= 0.003 m. Calculate the compressive stress O in the tube. Give your answer in N/mm2 to 2 decimal places. Figure Q2a Rectangular Tube Section Question 2 continues on the next page. MacBook Air DII DD 80 F9 F10 F6 F7 F8 F4 F5 F3 2$ & 3 # 4 6 7 8
*Inner quarter circles are hollowed sections *Use the center of the quarter circle R2 as the origin Using the figure above with R1=160mm and R2=150mm, calculate the following: ybar (location of the centroid along y axis), mm xbar (location of the centroid along x axis), mm
I will be selling a Summer Camp Innovative Sleeping System (SCISS) that suspends beds from the ceiling to make cleaning the floor easier (and to avoid snakes, bugs, and rodents). The top post is a 4-foot long steel post with a 2.5 inch x 2.5 inch cross section. The bottom post is a 3-foot long aluminum post with a 2 inch x 2 inch cross section. (a) What is the displacement of point “C" for the loading shown? (b) Has the yield stress of either post been exceeded? (c) What is the displacement of point “C” if the 120 lb loads are put on the top beds, and the 180 lb loads are put on the bottom beds? (d) For the loading in part (c), has the yield stress of either post been exceeded? 180 lb 120 lb -A- Steel Aluminum O 180 lb 120 lb
25 mm 20 mm 125 mm 2. A piece of sheet metal, with uniform thickness, is bent into the shape shown to the left. Find the center of gravity of the shape. Ans. I = 125 mm (by symmetry, no calculation required) y = 167mm, 7 = 33.5 mm. 80 mm 150 mm A 250 mm
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The hook is used to lift the force of P as shown. The section dimensions of a-a is given: P = 40 kN a = 25 mm b = 30 mm c = 70 mm a. Calculate the distance of the centroid of section a-a from the center of curvature in mm. b. Calculate the distance of the neutral axis of section a-a from the center of curvature in mm.
Find (Ix&ly), if a=30mm. a