2. Construct the circuit as shown below in Multisim, Voltage Source=1Vpk at 1kHz frequency R1=1kiloOHM, 1 V1 1V 1kHz 00⁰ D1 2 R1 1kQ 0 a.) What is the state of the diode when the input is positive cycle? (Explain in 1 phrase) b.) What is the state of the diode when the input is negative cycle? (Explain in 1 phrase) c.) Plot the output waveform of the circuit

2. Construct the circuit as shown below in Multisim, Voltage Source=1Vpk at 1kHz frequency R1=1kiloOHM, 1 V1 1V 1kHz 00⁰ D1 2 R1 1kQ 0 a.) What is the state of the diode when the input is positive cycle? (Explain in 1 phrase) b.) What is the state of the diode when the input is negative cycle? (Explain in 1 phrase) c.) Plot the output waveform of the circuit

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
What is CEMF?
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode. 4k02 2V 1k02. Off, 0.00mA, 0.4V O Off, -0.005mA, 0.0v On, 0.48mA, 0.6v On, 0.55mA, 0.7v Option 5
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
u= 6sinot V. V. For the circuit of Figure, we have known E=3V, Use the ideal diode model to analyze the circuit and draw the waveform of the output voltage. 6V cot Uj E
Considering a clamper circuit, where capacitance C, load R, the cut-in voltage of diode are unknown, which is the correct statement 1- the dc level of the signal changes 2- the peak-to-peak value of signal changes 3- the shape of signal changes 4- the dc level shifts up 5- the dc level shifts down
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
Draw the corresponding output waveform of the double diode partial limiter below using simplified diode model. Indicate all the necessary voltage levels and use Silicon diodes. 20 VP-P 1KQ M D1 9V D2 4.5V VOUT
A symmetrical Square wave of 2kHz whose voltage varies between +10V and -10V is applied to the given circuit. Find the maximum and minimum value of the voltage for the output waveform. Assume that the forward voltage and the forward resistance of the diode is 0 and reverse resistance is 2MOhm