2. Consider a narrow band fading channel with bandwidth B = 1Hz for which the SNR y has probability mass function for ₁ = 72 = 3,0 = probability 10 (b) 10 1 - P[y = ₁] = P[y = 72] = 0, In other words, y = ₁= with probability and y = 72 = 3 with Compute the Shannon capacity with CSI known at the receiver only. Compute the loss in rate between the capacity in point 2a and the capacity of the channel without fading and same average SNR as the channel in point 2a.

2. Consider a narrow band fading channel with bandwidth B = 1Hz for which the SNR y has probability mass function for ₁ = 72 = 3,0 = probability 10 (b) 10 1 - P[y = ₁] = P[y = 72] = 0, In other words, y = ₁= with probability and y = 72 = 3 with Compute the Shannon capacity with CSI known at the receiver only. Compute the loss in rate between the capacity in point 2a and the capacity of the channel without fading and same average SNR as the channel in point 2a.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Referring to the circuit: a.) Given that VDS2 = 2V ,find Iout b.) find the small signal parameters gm and ro of transistor M2 given that VDS2 = 2V M1 does not manifest channel length modulation while transistor M2 has λ = 0.03. M1 and M2 have the same dimensions, kp = 4mA/V2 and VTH,p = −0.3V. RB = 5kΩ and VDD = 5V.
1::YE 70 8.4 K/s 4. For SNR of 12.33 dB and signal power of 22.23 mW, the value of noise power is: 0.016 mW 0.3 W 1.3 mW 0.075 mW 5. If data can be transmitted in both directions but only one user can transmit at a given time, then communication system is said to be: Baseband communication system Simplex system Full Duplex system Half Duplex system
What is the relationship between the analog signal frequency F and the digital signal frequency f? (T is the period of the sampling period)a. F = f * Tb. F = F * Tc. No connectiond. Nothing is right
What is the reason for the error which is inevitably present on the PW demodulated signal? 4. Why a 100K resistor is connected across the 0.1 µf capacitor in the PW demodulator circuit? 5.
ASAP It is a type of diode where it operates as a variable resistor when heated. Your answer What is the modulation index in ideal condition of AM. Your answer A form of AM where a sideband is filtered after its carrier is eliminated. Your answer What is the form of AM that used to transmit video signals of the TV system? Your answer It is a circuit in the superheterodyne receiver that adds and subtracts the frequencies of the AM signal and the local oscillator frequency. It is the extent to which the amplitude of the carrier wave is varied by modulating wave.
9. The passband gain of practical passive Refilters in normally: a) Od b) 10 dB c) More than 0 dB d) Tess than 0 dB 10. The envelope of the transmitted AM signal is produced by the peaks of the a) Modulating signal b) Modulated signal ) The intermediate frequency d) The detector 11. If the carrict frequency received by AM receiver is 1.2 Milz the local oscillator should be set on one of the following frequencies: a) 1.2 MIIZ b) 455 kliz .) 2.4 MILZ d) 1655 MIIZ 12. Image frequencies in AM receivers are removed by: a) Low pass filter b) Band pass filters c) The I stage d) The mixer
You are required to design the Transmitter part of a digital communication system for transmitting an analog signal over a channel that can support a bandwidth of up to 1KH2 and also an SNR=30DB will be a good signal to noise ratio to work on this channel. Analog Input TX Channel RX Digital Analog Outpu" Signalling Keep in mind that the Transmitter should be composed of a PCM system and the system that generates the physical signals to be transmitted. Calculate the maximum Spectral Efficiency and continue your design with the max Data Rate (R=C) resulting with the max spectral efficiency. Also state how many levels should your M-ary (Multilevel) signal have in order to obtain this efficiency. Design the PCM system that will transform the input analog signal to digital and calculate the sampling period of the PCM system to obtain the bitrate necessary that is calculated. Please also state what should the Bandwidth of the Analog input signal be to be able to use this communication…
4. What do the Hartley's law tells us? A. Information capacity in a given channel is non-linear function of time and bandwidth B. Information capacity is linear function of time and bandwidth C. Information capacity is inversely proportional of the time and bandwidth D. All of the above
For over modulation, the value of modulation index m is a. m 1 d. Not predetermined
3. For the figure shown below what is the output voltage (V) of an amplifier for a given input voltage? Vout = ? Vin = 1 V 10 dB 4. For the S-matrix shown below find whether it is reciprocal or not and lossless or not? 0.220° 0.75Z90° [s]= 0.8290° 0.15Z0°
Ihe transfer function is quen as pallau Gis) - Design Requiement: 105 119.a5
If the bandwidth of a baseband signal is 10 Hz, what will the bandwidth of the signal be if it is multiplied by cos(1000πt)? O 5Hz O 200 Hz © 20 Hz O 100 Hz O 10 Hz O 500 Hz 4