2. A 4-pole shunt generator with a wave wound armature having 390 conductors supply a load of 500 lamps each of 100W, 250V. Allowing 10V for the voltage drop in the connecting leads between the generator and the load and a contact drop of 1-V per brush, what is the generated emf? The flux per pole is 30mWb; R₂ = 0.05 ohm and RSH = 65 ohm.

2. A 4-pole shunt generator with a wave wound armature having 390 conductors supply a load of 500 lamps each of 100W, 250V. Allowing 10V for the voltage drop in the connecting leads between the generator and the load and a contact drop of 1-V per brush, what is the generated emf? The flux per pole is 30mWb; R₂ = 0.05 ohm and RSH = 65 ohm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

There are 160 slots in a 3-phase, 8-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 150° electrical and the flux per pole is 0.08 Weber sinusoidally distributed. Calculate the emf induced per phase.
A DC generator has an armature emf of 500 V when useful flux/pole is 20 mWb, and a speed of 625 rpm. The generated emf at a speed of 125 rpm and same flux is
A 6-pole, 3-phase, 60-cycle alternator has 12 slots per pole and four conductors per slot. The winding is 5/6 pitch. There are 2,500,000 maxwells (0.025 weber) entering the armature from each north pole, and this flux is sinusoidally distributed along the air gap. The armature coils are all connected in series. The winding is wye-connected. Determine the open circuit emf of the alternator.
A dc 4 pole lap wound generator is running at 1000 rpm having 1200 conductors and flux density is 10 mwb. find the generated emf * O 10 V O 200 V O 100 V O 20 V
Q- In a DC generator, what will be change in emf induced if flux is reduced by 20% and the speed is increased by 20%.
AC Machinery Fundamentals A three-phase delta-connected six-pole winding is installed in 36 slots on a stator. There are 150 turns of wire in each slot of the windings. All coils in each phase are connected in series. The flux per pole in the machine is 0.060 Wb, and the speed of rotation of the magnetic field is 1000 r/min. What are the resulting phase and terminal voltages?
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D
1.) A 6-pole, 3-phase, 60-Hz alternator has 12 slots per pole and four conductors per slot. The winding is 5/6 pitch. There are 0.025 Wb entering the armature from each north pole, and this flux is sinusoidally distributed along the air gap. The armature coils are all connected in series. The winding is wye-connected. Determine the open circuit emf per phase of the alternator. Subject Electrical machine 2
A 50 Hz CT has 20 primary turns and 60 secondary turns, on a core of cross section 8 cm2. The secondary current is 5 amp. The impedance of the burden and the secondary winding are together equal to 0.7 + j 0.4 ohm. The excitation current required in the primary current to produce the working flux with the secondary open circuit is 0.6 angle 45 amp. Calculate the flux density in the core and the ratio and phase errors.
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
construct an winding diagram with -4 poles-26 conductors-double layer-simplex wave winding, 2 brushes
A wave wound armature of an eight-pole generator has 06 slots. Each slot contains 16 conductors. The voltage required to be generated is 300 V. What would be the speed of coupled prime mover if flux per pole is 0.05 Wb.If the armature is rewound as duplex lap wound machine and run by same prime mover, what will be the generated voltage.