2- What is the maximum shear stress in theshaft in (MPa)?8.635.753.6010.792.87None The steel shaft is made from twosegments: AC has a diameter of 50 mm,and CB has a diameter of 100 mm. If theshaft is fixed at its ends A and B andsubjected to a torque of 500 N.m, and Gst= 76 GPa.A50 mmD 500 N.m30 mm100 mm80 mm120 mm

Answered: Image /qna-images/answer/1d364108-2b77-4acf-9fec-1e8c7e947ba7.jpg

Answered: 2- What is the maximum shear stress in…

Engineering

Mechanical Engineering

2- What is the maximum shear stress in the shaft in (MPa)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft below is supported by 0.5 in long copper-iron light-duty journal bearings at A and B. Determine the maximum allowable shaft speed (in rpm) consistent with a bearing factor of safety of 1.8. F = 225 lbf Bearing A Bearing B 1.1 in Walow = ? 5.75 in 0.5 in 1.5 in 0.5 in
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
A bevel gear receives a power from bevel pinion results in the shown forces. The forces are F = 7026.8 i - 3513.4j+ 215840.8 k . the bevel gear average diameter is 210 mm. the shaft is supported at bearing E and F and delivers the power to a flange coupling at end G. the shaft is made of steel 826 M 40 H&T having Sy = 650 MPa and Sult = 850 MPa. Determine the shaft diameter at its critical section and make a complete construction drawing. Fr= 3513.4 N F, = 7026.8 N. F= 21584.8 N 100 mm 200 mm 105 mm
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
Given the shaft with multiple torques on it, calculate the internal torque developed in the BC segment: TBC = ____ N-m. If it is negative, please input the negative sign as well.
A spur gear transmits 35 N · m of torque to the 20-mm-diameter driveshaft. The 5-mm-diameter setscrew threads onto the gear’s hub, and it is received in a small hole that is machined in the shaft. What's the factor of safety aganist yield under shear loading
The driving shaft of a Hool joint rotates at a uniform sp. of 400 rpm. If the maxim variation in speed of the dri shaft is + 5% of the mean speed, determ the greatest permissible angle between axes of the shafts. What are the maxim and the minimum speeds of the driven sho
For the steel shaft shown in Fig. Draw a torque diagram for the shaft. 8 kN-m 15 kN-m 6 kN-m GGGGG T 14 kN-m
K QUESTION 9 Calculate the shaft diameter necessary to support a combined maximum bending moment of 2000 Nm, and an applied torsion of 300Nm. After considering the fatigue factor, the maximum allowable stress for the material is given as 228 N/mm². Give your answer in mm to 2 d.p. E.g 50.00 not 50mm πρ4 64 M C M+√M²+7² 2 QUESTION 10 and QUESTION 11 A pair of spur gears of module 3mm with 14 and 18 teeth are in mesh. What is the distance between centres in mm? Give your answer to 1 decimal place but do not include units in your answer eg 156.5 NOT 156.5mm. 1= A drive shaft is designed to transmit pure torque and is of diameter 20mm. It is made from steel with a Yield Strength of 220N/mm². What torque can it transmit if the usual allowances are made for materials in shear and torsion but no additional factors of safety are taken into consideration. Give your answer as a number in Nm to 2 decimal places. Don't include the units in the answer box eg 8.32 not 8.32mm Shaft Subjected to…
A taper roller bearing used in a windmill has a dynamic load capacity of 26 kN. The desired life for 90% of the bearings is 8490h and the speed is 350 rpm. The rated bearing life(L10) in millions of revolutions is . O a. 509.40 O b. 178290.00 O c. 17829.00 O d. 178.29 In a machine, the maximum torque transmitted by a shaft exceed by 23 % the actual torgue. A power of 3 kW has to be transmitted to another unit at a speed of 650 rpm. What should be the value of Maximum torque ? The maximum torque transmitted in N-m, When a component is subjected to fatigue loading, the endurance limit is the criterion for failure Select one: O True O False If "g" is the notch sensitivity, K, fatigue stress concentration factor, and k, the theoretical stress concentration factor. Identify the correct relation relating to these factors. (Ke-1)+(q)=(Kf - 1) O b. (K-1)=(Kf -1)*q O a. O c. (K-1)*(q)=(Kf -1) O d. (K,-1)-(q)=(Kf -1)
A 7/8 in. diameter shaft made out of ductile material is used to transmit power frommotor. The maximum allowable shear stress, τallow = 14.5 ksi is used for this shaft, andthe shaft rotates at 200 rpm. a. Find out the polar moment of inertia of the shaft. b. Find out the maximum Torque, T is being applied to the shaft. c. What would be the power of the motor?