2) In the circuit given in the figure, R = 6k2, Zener diode breakdown voltage VZ = 3.6V andwww mm wwwm wZener diode power value is given as 6.5mW.wwmthe maximum diode current that can flow through thewww w m m w mw ww m www md w mcircuit,Calculate the maximum voltage value that can be appliedw w mww m w w m www m wmentnVz=3.6 v Ato the circuit without damaging the diode.wm w w ww m ww

The given circuit is: Here, R=6 kΩVZ=3.6 VPZ=6.5 mW

2) In the circuit given in the figure, R = 6kN, Zener diode breakdown voltage VZ = 3.6V and www. w Zener diode power value is given as 6.5mW. the maximum diode current that can flow through the ww www mwm ww w circuit, Calculate the maximum voltage value that can be applied www V Vz= 3.6 v to the circuit without damaging the diode. ww m m m m

2) In the circuit given in the figure, R = 6kN, Zener diode breakdown voltage VZ = 3.6V and www. w Zener diode power value is given as 6.5mW. the maximum diode current that can flow through the ww www mwm ww w circuit, Calculate the maximum voltage value that can be applied www V Vz= 3.6 v to the circuit without damaging the diode. ww m m m m

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
What is CEMF?
u= 6sinot V. V. For the circuit of Figure, we have known E=3V, Use the ideal diode model to analyze the circuit and draw the waveform of the output voltage. 6V cot Uj E
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode. 4k02 2V 1k02. Off, 0.00mA, 0.4V O Off, -0.005mA, 0.0v On, 0.48mA, 0.6v On, 0.55mA, 0.7v Option 5
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Q1/ +5 V +50 V V R. Vin R 47 N 3.3 kN -5 V -50 V (a) (b) a. Draw the output voltage waveform for each circuit in above figure and include the voltage values. b. What is the peak inverse voltage across each diode? c. What is the peak forward current through each diode?
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
Determine the range of values of Vi that will maintain the zener diode in the "on" state in the figure below. Calculate IR and PRL ... R 220Ω RL 1.2KO VL. Vi Vz-20V Izmax-60mA
points) For the circuit shown below, sketch to scale the output V, waveform and draw the transfer characteristic (V. versus Vi), Assume the diodes are ideal. V₁ =15-sin wt Zloks www loks # HIF 4V + Vo