#2) A balanced, positive-sequence, 30 source having a phase voltage = 8020° volts is used to supply a Y-connected load, each phase of which has the impedance Zy=8-j692. The line current flowing out of phase "a" of the source is I = 8/36.9° amps. Specify all of the phase and line voltages of the source along with all of the line currents flowing in the system. Ĩ,= 7,= Ĩ,= ܠܪܐ ܠܪܐ 15 11 Ve 8020° + ZY ZY ZY

#2) A balanced, positive-sequence, 30 source having a phase voltage = 8020° volts is used to supply a Y-connected load, each phase of which has the impedance Zy=8-j692. The line current flowing out of phase "a" of the source is I = 8/36.9° amps. Specify all of the phase and line voltages of the source along with all of the line currents flowing in the system. Ĩ,= 7,= Ĩ,= ܠܪܐ ܠܪܐ 15 11 Ve 8020° + ZY ZY ZY

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.22P: A balanced Y-connected voltage source with Eag=2770volts is applied to a balanced-Y load in parallel...

See similar textbooks

Similar questions

A balanced Y-connected voltage source with Eag=2770volts is applied to a balanced-Y load in parallel with a balanced- load where ZY=20+j10andZ=30j15ohms. The Y load is solidly grounded. Using base values of Sbase1,=10kVAandVbaseLN=277volts, calculate the source current Ia in per-unit and in amperes
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
3. The single-line diagram of a three-phase power system is as shown in Figure Al-3. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW – j 33.4 Mvar, and at bus 3 is S3 = 77 MW +jl4 Mvar. It is required to hold the voltage at bus 3 at 40020° kV. Working in per unit, determine the voltage at buses 2 and 1. V2 V1 V3 j0.5 pu j0.4 pu S2 S3 Figure A1-3
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
a balanced three phase voltage of 100v line to neutral is applied to a balanced y connected load with undergrounded neutral . the three phase load consists of three mutually coupled reactances. each phase has a series reactance of Zs=j12 ohm and the mutual coupling between the phases is Zm=j4. determin the current using symmetrical components
A workshop from a 231/400 V transformer center with a 3-phase and four-conductor underground cablefed. The resistance of the phase conductors is 0.035 ohms and the resistance of the neutral conductors is 0.05 ohms.25 kVA at 0.8 reverse power factor from R phase of the supply line, 0.8 forward power factor from S phase 15Fully ohmic loads of 10 kVA are drawn from kVA and T phases.(a) Find the currents flowing through the phase conductors and neutral conductors.(b) Voltage drops between the transformer substation and the workshop and at the load terminals.calculate the voltages(c) Plot the supply line currents and phase voltages phasorally.
The plant capacity of a 3-phase generating station consists of two 8 MVA generators of reactance 14·5%each and one 4 MVA generator of reactance 9·5%. These are connected to a common bus-bar fromwhich loads are taken through a number of 3 MVA step-up transformers each having 4% reactance.Determine the MVA rating of the circuit breakers on (i) L.V. side and (ii) H.V. side. Reactances givenare based on the MVA of each equipment. [(i) 15·24 MVA (ii) 50·25 MVA]
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
Write an introduction about: LOAD BALANCING in 3-Phase System
Three single-phase transformers (ideal) are connected as shown in the figure below to supply a balanced 3-phase, 150 KVA, 600 VL load from primary 4.16 KVLL line. H1 X1 H2 X2 BALLANCED H1 X1 THREE PHAGE LOAD H2 X2 H1 X1 X2 (a) Draw (neatly) a phasor diagram showing the three, primary line-to-line voltages and the six secondary phase and line voltages. What is the phase relationship between the primary voltage VAB and the secondary voltage V12? Indicate on the phasor diagram:f