1Y1 1V2 182 1A 181 1V14 1Y2 2Y1 2A 2V2 2V14 251 ZM 252 After exchanging the adjustable one-way flow control valve 1V2 in the control circuit shown the supply port and working port are accidentally interchanged. Which would be the effect of this mistake on the operation of the control circuit? The piston rod of cylinder 1A will retract unthrottled at all times. Both chambers of cylinder 1A will be pressurized and its piston rod will remain in mid-position. After retracting cylinder 1A, it can not be brought in the extended end position anymore. The piston rod of cylinder 1A will be permanently in the forward end position. The piston rod's retracting movement will be throttled.

1Y1 1V2 182 1A 181 1V14 1Y2 2Y1 2A 2V2 2V14 251 ZM 252 After exchanging the adjustable one-way flow control valve 1V2 in the control circuit shown the supply port and working port are accidentally interchanged. Which would be the effect of this mistake on the operation of the control circuit? The piston rod of cylinder 1A will retract unthrottled at all times. Both chambers of cylinder 1A will be pressurized and its piston rod will remain in mid-position. After retracting cylinder 1A, it can not be brought in the extended end position anymore. The piston rod of cylinder 1A will be permanently in the forward end position. The piston rod's retracting movement will be throttled.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter23: Compressors

Section: Chapter Questions

Problem 15RQ: State the main advantage that a discus compressor's valve plate design has over a conventional...

See similar textbooks

Similar questions

1. Two double acting pneumatic cylinders (A, B) in a process industry should extend together at the same time to open two different valves. On the return stroke both cylinder rods return at the same time. The starting is by a detent switch. Both the cylinders are of the same size with the same stroke length. In terms of notation, the cycle is required to go on till the detent start-up switch is pressed again. Draw the electro pneumatic circuit neatly. Briefly explain its operation. LB +J LB A В Y Y Y Y V
Examine the circuit shown below and answer the following questions: 1. How is the cylinder 3A (towards the right) fundamentally different than cylinders 1A and 2A? 2. Describe 5 key features (ways, actuator, etc.) of the directional control valve 1V1. 3. Describe 5 key features of directional control valve 3V. 4. What type of device is 1V2? 5. Here's a close up of 1V2. Is it metering-in or metering-out? How do you know? 6. Empty triangle shapes appear in many places in this schematic. What do they represent? 1A 181 182 2A 282 3A 281 381 WWE 1V2 1V3 2V2 2V3 1V1 2V1 2Y1H svos H2Y2 3Y1 V 1V3 OV] OY1 211AM OZ
When using a flow control valve (needle valve) to control the speed of actuation of a cylinder, what needs to be added to the valve in order to maintain that speed under varying load pressures and why?
What would happen if one of the Flow Controls were reversed in a cylinder? What are the disadvantages by doing so?
In an IC engine the inlet valve diameter will be bigger than the outlet valve ? Select one: OTrue False
Which of the following is a symbol of the valve which continuously, resisting its flow even after work connection stops to the cylinder?
Which of the following statements is not true? A direct acting PRV: Is complex in construction, therefore can malfunction if a very small dirt gets trapped inside the valve, which may result in safety hazard Offers uneven flow Does not provide precise pressure control Causes more wastage of HP compared to a compound one Which of the following basic system components has the primary function of removing the heat of compression from the air? Receiver Relief valve Pressure regulator Dryer Aftercooler Which of the following statements is true? A single acting cylinder may have two ports at two different ends and pressurized fluid can be directed to both of them A single acting cylinder with two ports will can be used as a double acting cylinder A single acting cylinder may have two ports at two different ends but into only one of the ports pressurized fluid is being directed A single acting cylinder…
2. Which of the neutral condition of directional control valves for the following symbols are? А В A B A B А В UHIX P T P T P T PT
Draw the p-V diagram and typical valve timing diagram for a two stroke IC engine.
What is meant by regulator creep?
chapter33 question3 describe the operatoin of a digital EGR valve
19:07 * IZVA KOREK TELECOMIKOREK Asiacell МО The number 8 is pointed to the oil sump. O oil pump. air inlet manifold. water jackets. O exhaust manifold. cylinder head cover. O cylinder block. cylinder head. O