14. The resistance of the field coils of a dynamo is 173 Q at 16 deg C. After working for 6 hours on full-load, the resistance of the coils increases to 212 Q. Calculate the temperature of the coils. Assume temperature coefficient of resistance of copper is 0.00426/deg C at O * deg C. 62.5°C 52.5°C 82.5°C 72 50O

14. The resistance of the field coils of a dynamo is 173 Q at 16 deg C. After working for 6 hours on full-load, the resistance of the coils increases to 212 Q. Calculate the temperature of the coils. Assume temperature coefficient of resistance of copper is 0.00426/deg C at O * deg C. 62.5°C 52.5°C 82.5°C 72 50O

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.40P

See similar textbooks

Similar questions

The figure shows a conductor with four strands. Compute the GMR in terms of the radius r. Round-off your answer to 3 decimal places. Answer:
If the cross sectional area of a conductor is doubled, then the resistance of the conductor remains the same. becomes half of the initial value. becomes double the initial value. becomes four times the initial value.
Overhead transmission-line conductors are bare with no insulating cover. (a) True (b) False
A coaxial cable's shiled diameter is 0.4cm and the inner conductor has a diameter of 0.02cm. What is the characteristic impedance of that cable?
을 A circules ring of 3 turns iis made of Conducting wire. Now same wire The M.F. is bent to form ring of ctuong centre ( I Aome) at centre s B. Then flo M. F. at
temperature rating that a conductor must have and still have 69 Ambient Tempere 4. The ampacity of 15 current-carrying 10 RHW aluminum conduc- tors in a raceway in an ambient temperature of 75'F is 1. gon factor for conductor ampacity in this location is (a) 12A (b) 15A (c) 22A (d) 30A 0.71 b0.82 0.88 0.96 5. Ain) uous load if the ambient temperature is 75°F and there are nine THHN conductor is required for a 19.70A noncontin- ne ambient temperature is 71"C, the minimum insulation current-carrying conductors in the raceway in a dry location. he capacity to carry current is (a) 14 (b) 12 (c) 10 A 60°C AI 90°C 105°C (d) 8 0 120°C 6. 6.11 Ampacity Adjustment [310.15(B)(3)(a)] The ampacity for each of nine current-carrying 10 THW conduc- tors installed in a 20 in. long raceway is 1 The ampacity of six current-carrying 4/0 XHHW aluminum con- ductors installed in a ground floor slab (wet location) is (a) 25A (b) 30A (c) 35A (d) 40A a) 135A 0) 144A (e) 185A 4 210A
The figure below shows a ring distributor with interconnector BD. The supply is given at point A. The resistances of go and return conductors of various sections are indicated in the figure, current in the interconnector and voltage drop in the interconnector are: 10 A 0.075 2 B 0.025 2 0.12 0.05 2/ + 30 A 0.01 a 10 A 0.05 2 20 A
A transmission line cable consists of 19 strands of identical copper conductors, each 1.5 mm in diameter. The length of the cable is 2 km but because of the twist of the strands, the actual length of each conductor is increased by 5 percent. What is resistance of the cable ? Take the resistivity of the copper to be 1.78 ×10^–8 m.
10/ Sag increases when the conductor ages due to this effect. A. THERMAL EXPANSION B. ELASTIC STRETCH C. METALLURGICAL CREEP D. STAY RELAXATION
The diameter of an ACSR conductor is 1.1116 inches. The steel core has strands of diameters of 0.1291 inches each. If 54 Aluminum strands have the diameters of 0.1351 inches each, the number of Steel strands is: O A. 15 O B. None of choices are correct O C. 19 O D.7 O E. 27
Pure iron has a resistivity of 10.0 x 10-6 ohm-cm at 20 ° C. The resistivity of copper at this temperature is 1.77 × 10-6 ohm-cm. Consider two different conductors, each 1 meter long and a square straight section 0.8 cm on each side. Conductor A is formed by joining end to end a 50 cm long iron bar with a similar copper rod. Conductor B consists of a copper rod and an iron rod 1 meter long with a 0.4 by 0.8 cm cross section, joined laterally. What is the resistance in ohms of each conductor, between the ends 1 meter apart? If a steady current flows in conductor A, in which material will the power dissipation be greater. Answer the same question for bar B
Question 1 Select all that apply. Which of the following are considered to be "core losses"? 12R heating loss Flux lines that bulge out at core gaps Currents that circulate within the machine non-ferrous components Field Lines that circulate around conductors and coils Rapid Changes in Domain orientation