12. A horizontal shaft AD supported in bearings at A and B and carrying pulleys at C and D is totransmit 75 kW at 500 r.p.m. from drive pulley D to off-take pulley C, as shown in Fig. 14.18.P₁AIPE-P₂-600600-300-9₂All dimensions in mm.Fig. 14.18Calculate the diameter of shaft. The data given is: P,-2 P, (both horizontal), Q, 2 Q₂ (bothvertical), radius of pulley C-220 mm, radius of pulley D 160 mm, allowable shear stress - 45 MPa.[Ans. 100 mm]

Answered: Image /qna-images/answer/f23b7cf0-90c6-4c7f-b2e3-b12aef13b136.jpg

12. A horizontal shaft AD supported in bearings at A and B and carrying pulleys at C and D is to transmit 75 kW at 500 r.p.m. from drive pulley D to off-take pulley C, as shown in Fig. 14.18. D -P₂ -600 600- 300- All dimensions in mm. Fig. 14.18 Calculate the diameter of shaft. The data given is: P₁ - 2 P, (both horizontal). Q₁-2 Q₂ (both vertical), radius of pulley C-220 mm, radius of pulley D-160 mm, allowable shear stress - 45 MPa. [Ans. 100 mm]

12. A horizontal shaft AD supported in bearings at A and B and carrying pulleys at C and D is to transmit 75 kW at 500 r.p.m. from drive pulley D to off-take pulley C, as shown in Fig. 14.18. D -P₂ -600 600- 300- All dimensions in mm. Fig. 14.18 Calculate the diameter of shaft. The data given is: P₁ - 2 P, (both horizontal). Q₁-2 Q₂ (both vertical), radius of pulley C-220 mm, radius of pulley D-160 mm, allowable shear stress - 45 MPa. [Ans. 100 mm]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The polar modulus for a solid shaft of 40 mm diameter is
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
10. Aline shaft is to transmit 30 kW at 160 r.p.m. It is driven by a motor placed directly under it by means of a belt running on alm diameter pulley keyed to the end of the shaft. The tension in the tight side of the belt is 2.5 times that in the slack side and the centre of the pulley over-hangs 150 mm beyond the centre line of the end bearing. Determine the diameter of the shaft, if the allowable shear stress is 56 MPa and the pulley weighs 1600 N. [Ans. 60 mm
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
A shaft made of 40 C 8 steel is used to drive a machine. It rotates at 1500 r.p.m. The pulleys A, B and the bearings C, D are located as shown in Fig. 14.21. The belt tensions are also shown in the figure. 350 N 165 N 330 N A B 135 N B D 45° 200 200 300 200- 300 All dimensions in mm. Fig. 14.21 Determine the diameter of the shaft. The permissible shear stress for the shaft material is 100 MPa. The combined shock and fatigue factor applied to bending and torsion are 1.5 and 1.2 respectively.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
1. The endurance limit for rotating shaft, if its ultimate strength Su=1600 Mpa is:
A 7/8 in. diameter shaft made out of ductile material is used to transmit power frommotor. The maximum allowable shear stress, τallow = 14.5 ksi is used for this shaft, andthe shaft rotates at 200 rpm. a. Find out the polar moment of inertia of the shaft. b. Find out the maximum Torque, T is being applied to the shaft. c. What would be the power of the motor?
! Required information A 24-mm-diameter uniform steel shaft is 600 mm long between bearings. Take the value of acceleration due to gravity g to be 9.81 m/s2, the value of y for carbon steel to be 76.5 × 103 N-m-3, and the value of Eto be 207 x 10⁹ N/m². NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the critical speed of the shaft in rads/s? (You must provide an answer before moving to the next part.) The critical speed of the shaft is 847.5 rad/s.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 400 The shaft is mounted on two 400 400 270 250 ]640 210 640 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 100
A 7/8 in. diameter shaft made out of ductile material is used to transmit power frommotor. The maximum allowable shear stress, τallow = 14.5 ksi is used for this shaft, andthe shaft rotates at 200 rpm. a. Find out the polar moment of inertia of the shaft. b. Find out the maximum Torque, T is being applied to the shaft. c. What would be the power of the motor? d. What are the general state of stresses for this application? Is it plane stress? Pleaseshow the general stress information, choosing any point in the shaft and zoomingin that point. e. If the shaft fails, how will it fail? Show it by a free hand sketch. f. What will be the maximum in-Plane shear stress, and its associated average normalstress? Please use the analytical equations. ONLY D, E, & F PLEASE