11. The observed interior angles of a four-corner lot and their corresponding number of observations are given in the table: Corner Interior Angle Number of observations A 132° 6. B 68° 96° 67° Determine the corrected angle of comer C c. 94°56.84' a. 95°56.84 b. 97°3.16 d. 96°3.16

11. The observed interior angles of a four-corner lot and their corresponding number of observations are given in the table: Corner Interior Angle Number of observations A 132° 6. B 68° 96° 67° Determine the corrected angle of comer C c. 94°56.84' a. 95°56.84 b. 97°3.16 d. 96°3.16

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rectangular footing has dimensions shown and is acted upon by a dead load of 570.00 kN and a live ...

A: We have to determine the value of ratio of the Ultimate Shear Force to Shear Capacity in two way she...

Q: The mass of an empty gas jar was 0.498 kg. When completely filled with water, its mass was 1.548 kg....

Q: find the load on the guy anchore and the horizantal force on the pole 400lb 10ft 400lb 5ft 100ft 400...

Q: Two forces of magnitude T, = 10kips and Tc =15kips are appl shown to a welded connection. Knowing th...

A: According to given data

Q: A two-lane rural roadway segment is expected to have 15 crashes (total) durch year with AADT of 1800...

Q: The top of a tower signal at B 2000 m away from A was sighted through a transit with recorded vertic...

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as show...

A: Determine stress in each section

Q: The motion of a particle is governed by the relation a = 4t² , where a is in m/s² and t in secs. Whe...

Q: 100 mm 50 mm diameter diameter 3 kN m 1 kN m 200 mm 400 mm

Q: In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix pro...

Q: Determine the value of degree of saturation if void ratio is 0.35, Specific gravity of soil is 2.5 a...

A: Given Specific gravity of soil, G= 2.5 Water content, W = 35% = .35 void ratio, e= 0.35 Formula use...

Q: A uniform beam weighing 1800 N is supported at E and F by cable ABCD. Determine the tension (in N) i...

Q: scuss some of the significant challenges faced by the designer and the builders

Q: A 7.15° horizontal curve has a central angle of 36.7°. If the station of PT is at 25+198, determine ...

Q: As shown in the figure, two blocks are connected by a light, flexible cord passing over a frictionle...

Q: W14 x 82 A992 steel 13'

Q: What Curves that generally used to provide a gradual change in curvature from a straight section of ...

A: Curves that are generally used to provide gradual change in curvature from a straight section of a ...

Q: What are the equations that describe the ductile creep of rocks at low, moderately low (<200 MPa) an...

A: Creep is the term for a material's long-term strain response.

Q: The section of a gravity dam is as shown in the figure. Assume hydrostatic uplift "U' to vary unifor...

A: Given data W1 = 224640 lbs W2 = 44928 lbs W3 = 71884.8 lbs W4 = 56160 lbs U = 131040 lbs F = 112320

Q: 1. A butt joint is fastened by 20 mm diameter bolts as shown in the figure. Assuming that the axial ...

Q: ant rotational speed such that the absolute v out and observes a friend who is in car B. kinematic d...

A: According to given data shows a ferris wheel in an amusement park has eight equally spaced cars. T...

Q: Solve for the concrete materials of slab, beams and girders using class "A" concrete.

Q: w= 12 kips/ft 6 kipe D hinge

Q: solid steel shaft ABC of 50mm diameter is driven at A by a motor that transmits +50kW to the shaft a...

Q: A truck, with four wheel configuration and has loads as shown, will cross to a 12 m span bridge. A b...

Q: For the loading shown in Figure 5, detemine the required intensity (w) and the dimension (d) of the ...

A: To compute the load intensity (w) and the distance (d) for the given conditions. Given, Condition...

Q: tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of...

Q: As shown in the figure, two blocks are connected by a light, flexible cord passing over a frictionle...

Q: .In a water supply scheme to be designed for serving a population of 400000, the storage reservoir i...

Q: Given data : Stress=70 Mpa E=800 MPa Determine the value of strain

Q: In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect any mix pro...

Q: You must show all pertinent solutions and the illustration that supporting the answer. Please list t...

A: To determine: acceleration of each block tension in the cable Given, Mass of block A (MA) = (21 ...

Q: Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced th...

A: Given, Sieve analysis data

Q: Determine the nominal axial compressive strength of the members shown in the following figure. 1. Pi...

Q: What is the importance of understanding the work done by a force, the correlation between work and e...

Q: f) P Joint 2 rigid 2.2.17 Consider the truss of Figure 2.12f with a rigid joint at 2. (a) Solve Per ...

Q: A solid steel shaft ABC of 50mm diameter is driven at A by a motor that transmits +50kW to the shaft...

A: Diameter of shaft = 50 mm frequency of shaft = 10 Hz Power at A = 50 KW Power at B = -35 Kw power at...

Q: A 82.5g of iron shot is added to graduated cylinder containing 45.5cm'of water. The water rises to t...

Q: 2. The 1-m diameter cylinder in the figure is 8 meters long (dimension perpendicular to the paper) a...

Q: correct stress state for representing the circumference of the pressure vessel is which o owing:

A: In circumference,only the hoop stress will gets developed. Hoop stress = pr/t Hence option is D .

Q: A water supply main trifurcates at a junction point J into thre branches each feeding a separate res...

Q: The mass of an empty gas jar was 0.498 kg. When completely filled with water, its mass was 1.548 kg....

Q: 2. The simply supported beam below is supported on a spring at joint 2. (a) Compute the stiffness co...

Q: SITUATION. In a certain Direct Shear Test Experiment the sample fails at shear stress of 8 kPa when ...

Q: 1. Determine the percent finer for each sieve and plot the grain size distribution curve. 2. Determ...

A: Step: 1 “Since you have posted a question with multiple sub-parts, we will solve first three subpart...

Q: Situation 2: An open cylinder vessel 1.2 m in diameter contains water at a depth of 3.75 m. 3) If it...

A: D=1.2m r=0.6m N1=85rpm NE=125rpm

Q: 2.0m What is the support reaction Ve from the following figure? 10 kN 10 kN 10 kN D E HA 2.0m 2.0m 2...

A: The given numerical is related with truss topic . In this question we are provided with value of loa...

Q: The five major forms of resistance to a vehicle's movement are: 1. inertia 2. grade 3. rolling 4. cu...

A: Given, →Inertia resistance, is the resistance offered by the virtue of inertia of a vehicle. It is e...

Q: G=1.5 Wz4x55 G=1.5 Iz' cz: CZ Wz4x55 Question 24 G=3.0 G=3.0 The frame shown is the plane of the fra...

A: Frame structures are the constructions having the blend of pillar, segment and piece to oppose the s...

Question

11. The observed interior angles of a four-corner lot and their corresponding number of observations are
given in the table:
Corner
Interior Angle
Number of observations
A
132°
6.
B
68°
4
96°
67°
Determine the corrected angle of comer C
c. 94°56.84'
d. 96°3.16'
a. 95°56.84'
b. 97°3.16

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. What are the radian and degree-minute-second equivalents for the following angles given in grads: (a)* 136.000 grads (b) 115.089 grads ???°??′??″; 1.80781 rad (c) 363.809 grads ???°??′??″; 5.71469 rad
From the following measured interiror angles of a five sided figure, compute the following: Station Values of Angles (No. of Measurements 110.00 98.000 108.00 120.00 105.00 ABCDE 5642 NOTE: Final answer must be in decimal degrees. HINT: Sum of Interior Angles = (n-2)*180* 2 1 a) Probable value of Angle A. "b) Probable value of Angle C. c) Probable value of Angle D
Question 8 The angles about a point P were measured with the following number of measurements taken shown in the table below. Measured Angle Repitition Value APB 31° 15' ВРС 12° 16' 4. СPD 41° 28' 4 DPA 84° 53' Calculate the most probable value of angle BPC O 12°14' O 12°17 O 12°18' O 12°15'
FUNDAMENTALS OF SURVEYING Triangulation stations A,B, C and D has the following observation angles. Angle Values ACB 50 deg BAD 20 deg BCD 30 deg ABC 50 deg CAD 60 deg a. Find the angle CDB b. Find the angle BDA c. Find the angle BDC
Triangulation stations A,B,C and D has the following observation angles. Angles: ACB=50° BAD=20° BCD=30° ABC=50° CAD=60° a. Find the angle CBD. b. Find the angle BDA. C. Find the angle BCD.
From the following observations, what is the closing error? Line AB BC CA O a. 1.66 b. 1.55 c. 1.44 O d. 1.99 Length (m) 92.96 157.63 131.24 Latitude +92.57 -317.39 +226.19 Departure -217.92 +24.62 +192.36
From the following measured interiror angles of a five sided figure, compute the following: Station Values of Angles (No. of Measurements A 110.00 98.000 108.00 120.00 105.00 BUDE с 5 NOTE: Final answer must be in decimal degrees. HINT: Sum of Interior Angles = (n-2)*180* NAO сл 6 4 2 1 a) Probable value of Angle A. b) Probable value of Angle C. °c) Probable value of Angle D
S LINEAR ERROR OF CLOSURE N Problem 2: W E U For the given data of a transit-tape survey. S 1. Determine the latitudes and departures of the lines. 2. Determine the linear error of closure. 3. Determine the bearing of the line of the side error. V 4. Determine the relative precision. LINE LENGTH (m) BEARING LATITUDE DEPARTURE +N -S +E -W Y AB 495.85 N 05°30'E BC 850.62 N 46°02'E CD 855.45 S 67°38'E DE 1020.87 S 12°25'E EF 1117.26 S 83°44'W FA 660.08 N 55°09'W Total ΣNL ΣSL ΣED EWD 3 RVE
A closed-loop traverse ABCDA was run around an area and the following observations were made: Length Included angle Station W.C.B. at to (m) A 187.4 86°30'02"| 140°11'40" B B 382.7 80°59'34"| C C 106.1 91°31'29" D D 364.8 100°59'15" A Adjust the angular error, if any, and calculate the coordinates of other stations if the coordinates of the station A are E1000 m and N1000 m.
kindly answer immediately this is in the surveying subject -If the azimuth is 270°, the compass quadrant bearing is: choices: a. S 6° W, b. due west, c. 6° SW, d. due NW -On Problem ABC. What will be the probable error of the single. choices: a.0.028, b.0.020, c. 0.035, d. 0.022 -Responsible to the accuracy and speed of all linear measurements of tape choices: a. Head tape man, b. Rear tape man, c. Rodman, d. Pacer -If the azimuth is 111°, the compass quadrant bearing is: choices: a. S 69° E, b. N 11° W, c. E 11° S, d. 21°
Two angles BAC and CAD and a single angle BAD are measured at the same point A. Determine the most probable value for each angle. ANGLE Observed value No. of measurement ВАС 28°24'00" 1. CAD 61°15'00" 3 BAD 89°24'00"
From the following observations, what is the closing error? Line AB BC CA O Length (m) 92.96 157.63 131.24 a. 1.44 O b. 1.99 C. c. 1.55 O d. 1.66 Latitude +92.57 -317.39 +226.19 Departure -217.92 +24.62 +192.36 <