Draw a figure or FBD that will support the problem. Explain each step by step formula. 11. Consider the figure below. Each tank has a volume of 1Oft. Conditions on each tankis tabulated as follow:kTank No.ContentPressureTemperature70psia160°F1.32Methane1.24Propane21psia124°F3Нехаne43psia110°F1.39TANK 1TANK 1TANK 1All separation valves have been opened at the same time. Determine the resultingtemperature in "F at equilibrium.

Answered: Image /qna-images/answer/79b9bd3b-17b2-4d57-ac0c-f5ef9f5cea9c.jpg

11. Consider the figure below. Each tank has a volume of 10ft. Conditions on each tank is tabulated as follow: k Tank No. Content Pressure Temperature 1 Methane 70psia 160°F 1.32 1.24 Propane 21 psia 124°F Нехane 43psia 110°F 1.39

11. Consider the figure below. Each tank has a volume of 10ft. Conditions on each tank is tabulated as follow: k Tank No. Content Pressure Temperature 1 Methane 70psia 160°F 1.32 1.24 Propane 21 psia 124°F Нехane 43psia 110°F 1.39

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q8 The bore diameter of each cylinder in a three-cylinder two-stroke petrol engine is 14.71 mm and the stroke length for each cylinder piston is 250.25 mm. During engine testing, the engine runs at 300 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 6.8 cm2 and area length of length of 2.6 cm. For a pressure scale of 350 kN/m2 per cm on the indicator diagram, calculate the indicated power developed by the engine. Give your answer in kilowatts (kW) to 2 decimal places. Pressure versus Volume Indicator Diagram (Pressure scale = 350 kN/m² per cm) Peak Pressure Enclosed net area for engine work done m.e.p Diagram length, cm Diagram height, cm
27. A closed vessel contains air at a pressure of l130 kN/m´ gauge and temperature of 30°C. The air is heated at constant volume to 60°C with the atmospheric pressure of 759 mmHg. What is the final gauge pressure?
10 m3 of free air is compressed to 8 bar gauge, every minute. What will be the air volumetric flowrate at the compressor exit if air is assumed an ideal gas ? please choose correct option a.1.11 m3/min b.2πdt m3/sec c.1.27 litre/sec d.1.11 m3/hour e.2.2 litre/sec
Q1. Answer the following: - A- What are the differences between the heat and temperature? B- List two important factors that the specific heat of a gas depends on these factors? C- List three applications in your home depend on thermodynamic principle operation? D- Name the parameter that the nozzle utilizes to produce an increase in the kinetic energy? E- What is the important factor that the potential energy depends on it?
Provide a complete given and computation. Include all the decimals. A 12 x 14 in double-acting air compressor with 5.5% clearance operates at 150 rpm, drawing air at 14.5 psia and 85 ̊F and discharging is at 62 psia, the compression and expansion processes are polytropic with n=1.34. Determine: a) The volume of free air handled per minute, if atmospheric conditions are 82 ̊F and 14.7 psia, b) The heat rejected, c) The indicated work of the compressor if the compression efficiency is 87% d) The ideal work
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 1, P1(gage)=______ A. Patm B. 0 C. 101.325 kPa D. It can not be determined.
Consider a tank filled with ultra high purity nitrogen. The pressure gage reads 14898.7 kPa. The ambient pressure in the laboratory is 1 atm. The volume of the tank is 1 m3. You use the gas to purge analyzers and a mass flow controller is set to deliver this gas at 0.25 kg/min. How many hours can you purge your analyzers. Please list any assumptions REDMI NOTE 8 PRO AI QUAD CAMERA Activate Windows
On the Mindray A5/A3, during the leak test the pressure indicated by the airway pressure gauge fails to reach 30 cmH20. What should you check?
An unknown ideal gas at 53 deg F and 3.3 in Hg (gauge) is flowing through an irregular duct. To determine the flow rate of the gas, carbon dioxide, from a modular carbon dioxide tank, is passed into the gas stream. The gas analyzes 1.2% CO2 before and 3.4% after addition. The tank is on a scale and found to lose 12 lb in 10 minutes; What is the flow rate of the ideal gas in ft^3/minute?
b) The bore diameter of each cylinder in a sir-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing, the engine runs at 1450 revolutions per minute (pm) with a pressure-volume indicator diagram showing a mean net area of 2 90 cm' and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kNmper cm Calculate the mean effective pressure (mep) and the indicated power in klowatts (aW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal places. c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. the maximum allowable stress for this hollow rod is 325 KNimm, calculate the minimum thickness of the rod. Give your answer in millimetres (mm) and to 2 decimal places.
Get the following values for each stage using NIST tables: Stage 5(feed water in): P5, T5, H5 Stage 6(feed water out ): P6, T6, H6 Explain how to get values please.
FLUID MECH Support your answer with the appropriate solution and diagram. 5. Air at 2.50 kg/m^3 enters a nozzle that has an inlet to exit ratio of 2:1 with a velocity of 120 m/s and leaves with a velocity of 330 m/s. Determine the density of air in kg/m^3 at the exit. A. 1.02 B. 1.82 C. 2.78 D. 4.02