10 kN/m B__2 -6 m 6 m

Q: What is the magnitude of the reaction at point E? 40 kN 20 kN/m 100 kN-m |C D - 2 m 2 m 2m -

A:

Q: The unstretched length of spring AB is 4 meters. If the block is in the equilibrium position,…

A:

Q: The member shown is pin-connected at A and rests against a smooth support at B. Determine the…

A:

Q: Determine the reactions at points of contact A, B, and C needed to support the force of 800 N.…

A: To find reaction at point A, B and C

Q: The collar has a weight of 50 lb and falls down the titanium bar. If the bar has a diameter of 0.5…

A: Write the formula for static deflection of the given load i.e. the weight of the collar. Here, P is…

Q: The beam has a constant E1I1 and is supported by the fixed wall at B and the rod AC. If the rod has…

A: Using superposition net deflection at point A can be determined as Deflection at A due to UDL on…

Q: The rigid bar is supported by the two short white spruce wooden posts and a spring. If each of the…

A:

Q: The post is made of Douglas fir and has a diameter of 100 mm. If it is subjected to the load of 20…

A: Write the expression of the frictional resistance considering the distribution of load as triangular…

Q: "Determine the reactions on the beam. The support at B can be assumed to be a roller and A a pin.…

A:

Q: Q1. The forearm and biceps support the 10-kg load at A. If, the smallest cross sectional area of the…

A: First of all, make a FBD of the diagram as shown below,

Q: Q3: The uniform beam has a mass of 50 kg per meter of length. Determine the reaction the supports.…

A: GIVEN:

Q: Problem #2: If the gap between C at the rigid wall at D is initially 0.15 mm, determine the support…

A:

Q: Q2 / The boom is intended to support two vertical loads, F, and F2. If the cable CB can sustain a…

A:

Q: The pipe can be assumed roller supported at its ends and by a rigid saddle C at its center. The…

A: Free-body diagram of a pipe is given as, On using equilibrium of force in a vertical direction,…

Q: 9.49. If the gap between C and the rigid wall at D is initially 0.15 mm, determine the support…

A: Given Data: The applied load is P = 200 kN. The gap between wall and D is x = 0.15 mm. Dimensions…

Q: 1. Determine the reactions acting on the smooth uniform bar, which has a mass of 20 kg. 4 m 60 30

A:

Q: Determine the horizontal and vertical components of reaction at the pin A and the reaction or beam…

A:

Q: Determine the reactions at A and B .for equilibrium of the member in fig 50 -150'N 0.7m- 0.7 m A 20…

A: Taking average forceF1=50+1502F1=100 NAnd F2=20+802F2=50 N

Q: Determine the required length of the cord AC, So that the 8 kg lamp can be suspended in the position…

A: When a body is in static equilibrium, the net external force acting on the body is equal to…

Q: 0.4 m 0.4 m F = 600 N B. y A 30 Determine the horizontal and vertical components of reaction at the…

A: Find the reactions on the support and normal force on the peg B

Q: If the weight of the boom is negligible compared with the applied 30 kN load, determine the cable…

A:

Q: Determine the support reactions of roller A and the smooth collar B on the rod. The collar is fixed…

A: Consider the free body diagram of the system.RA is the reaction at B and RB and MB are the reactions…

Q: The assembly consists two different sections with diameter of 40 mm and 20 mm, respectively. If the…

A:

Q: The 30 kg block is supported by two springs having the stiffness shown. Determine the strech of…

A: Consider the free body diagram: tanθ=0.30.4θ=36.86°tanϕ=0.40.4ϕ=45°Applying Lami's…

Q: The 500-kg large chandelier is suspended from the wall and ceiling using rods AB and BC which have…

A: The free-body diagram of the given system will be as follows, The data given is, Diameter of rod…

Q: Determine the horizontal and vertical components of the reaction at support A of the frame shown in…

A: Free body Diagram Taking Y direction equilibrium, Ay + By - 200 - 450 - 625 = 0 Ay + By = 1275 N…

Q: The beam AB is supported by pin at A and roller at B. Determine the magnitude of the vertical…

A:

Q: The bent rod is supported at A, B, and C by smooth journal bearings. Determine the components of…

A:

Q: F16-11. Determine the reaction at the roller B. El is constant. SOKN -4 -2 m- 6 m-

A: Consider the reaction at B is redundant, Then the reaction at the support will be, RA=50×812RA=1003…

Q: A 800 N 600 N B 0.8 m (0.4 m 0.4 m 0.8 m

A:

Q: The beam is subjected to the two concentrated loads. Assuming that the foundation exerts a linearly…

A:

Q: The rigid beam is supported by three 25-mm diameters A-36 steel rods. If the beam supports the force…

A:

Q: Q2. Determine the force reaction exerted on the rigid support, when the temperature is raisevt hv 10…

A:

Q: P4-7. Determine the force P needed to cause impending motion of the block. 1m w = 100 N EIm . = 0.4

A: Given data: Weight of the block, W = 100 N. Coefficient of friction, µs = 0.4. Consider slipping…

Q: F16-12. Determine the Teaction at the foller support B if it settles 5 mm. E – 200 GPa and I -…

A: Given; W = 10 KN / m E = 200*109 GPa I = 65.0*10-6 m4     Solving UDL; W = 10*12 = 120 KN at 6m…

Q: 6] Determine the required length of cord AC in Fig.below so that the 8-kg lamp can be suspended in…

A:

Q: The beam is subjected to a load F = 275 N and is supported by the rope and the smooth surfaces at A…

A: Fig: FBD of the beam

Q: Q3: The uniform beam has a mass of 50 kg per meter of length. Determine the reactions at the…

A:

Q: Determine the maximum weight of the engine that can be supported without exceeding a tension of 450…

A: Given  The value of tension in chain AB is FAB=450 lb. The value of tension in the chain AC is…

Q: Determine the required length of the cord AC, So that the 8 kg lamp can be suspended in the position…

A: When a body is in static equilibrium, the net external force acting on the body is equal to…

Q: The beam has a constant E1I1 and is supported by the fixed wall at B and the rod AC. If the rod has…

A:

Q: the cylinder with a mass of 1000 Kg is supported as shown in the figure, determine the reactio

A:

Q: 5. If the weight of the boom is negligible compared with the applied 30 - kN load, determine the…

A: Draw the FBD for the given question.

Q: If the weight of the box 10 W determine the cable tensions TAB, and TAC and TAD. 3 ft 2 ft 3 ft B 2…

A: Find the tension force in each cable.

Q: If the tension in the spring is 600, the vertical component of the pin reaction at B is:

A: Given, Tension in spring = 600 lb

Q: 200 N 6. 15 E= 100 6pa V= 0.a5 0:5 m

A:

Q: 3m FRONT 2m 6m 2m y N

A: Given, Wind Pressure P = 5 kPa Tension in cable T = 12 kN

Q: А - 3 ft 3 ft 2 ft 30° Determine the horizontal and vertical components of reaction on the member at…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.