10 kN/m B 20 KN 4 m 2 m 2 m a. Draw the shear diagram of the beam. b. Draw the moment diagram of the beam. c. What is the magnitude of the maximum moment? d. Design a rectangular section with proportions d = 2b for the maximum moment if Fb = 15 MPa. e. What is the magnitude of the maximum shear? f. Design a rectangular section with proportions d = 2b for the maximum shear if Fv = 1.5 MPa. g. Design a rectangular section with proportions d = 2b if the maximum deflection should not exceed 20 mm. Use E = 7.3 GPa.

10 kN/m B 20 KN 4 m 2 m 2 m a. Draw the shear diagram of the beam. b. Draw the moment diagram of the beam. c. What is the magnitude of the maximum moment? d. Design a rectangular section with proportions d = 2b for the maximum moment if Fb = 15 MPa. e. What is the magnitude of the maximum shear? f. Design a rectangular section with proportions d = 2b for the maximum shear if Fv = 1.5 MPa. g. Design a rectangular section with proportions d = 2b if the maximum deflection should not exceed 20 mm. Use E = 7.3 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. dw C 4 in. dp B 15° 5 in: View a-a of B P = 200 lb.
Week 5, Question 2: Using the force method, calculate the bending moment at B for the statically indeterminate frame below. Please ignore the axial and shear deformations. Take a 12 kN and L = 5.5 m. a B EI A 2EI -3 m Calculate the bending moment at B: kN m MB 2EI m D EI E +=+ L
A cantilever beam AB, loaded by a uniform load (see figure), is applied on a channel section. If the cross section has the dimensions indicated and the moment of inertia about the z axis (the neutral axis) is | = 3.36 in a) Find the maximum tensile stress feuaxand maximum compressive stress fyMx b) Draw the shear and moment diagram 5.0 lb/ft 0.617 in. 2.269 in. 6.0 ft
calculate the location of the centroid, the second moments and product of area for the cross- section if; D = 67 mm, B = 41 mm & t = 2.41 mm A L Test beam A Strain gauge W (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 Strain gauge 2 b Strain gauge 3 a B (b) Location of Huggenberger strain gauges From these, calculate the orientation and position of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis).
#09 10 in. 4 in. B H 280# 18 in. 1.2 in. Three forces are applied to lever ABD. (a) Draw Mohr's Circle for Point H, (b) determine the max in-plane shear stress and the associated plane at the point H. D X 300#
Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. 150 P=300lb. -5 in- dw ↓ 1 4 in. D View a-a of B
Problem 5 The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20000 psi? the 3/4 in diameter pin is in double shear. ANS: P = 19770 lb-f A 10 in. B 30° P 12 in. C
Questions a/b c₁ = c₂ = c 5 0.291 10 0.312 20 0.323 40 0.328 200 10 E m 200 10 1. 6.3 kNm torque is applied to a 3m long steel angle with a 200mm x 200mm x 10mm cross section. From tabulated properties for equal angles, the gross cross sectional area of the section is 5090 mm². knowing that G = 77 GPa, determine (a) the maximum shearing stress along line m-m. Provide the answer in MPa with precision n to two decimal points. 2. Determine the angle of twist if 1.7 kNm of torque is applied to the above long angle steel. Provide the answer in Degrees with precision to two decimal points.
An assembly of bars are designed in Figure 1. The assembly is made of structural A-36 steel where bar AB and BC has a drameter of 50 mm. ASTM and 25 mm The respectively. determine дар between C and the rigid wall at D is initially 0-15 mm, the support reaction at A and D when the force P= 292 kN is applied at B 600mm 450mm 292- A B D
Question 6 Horizontal force P = 600 N magnitude applied to end D of lever ABD. Find (a) normal and shearing stresses on element at H having sides parallel to x and y axes (b) principal planes and principal stresses at H. P= 600 N В T= 270 N.m. 450 mm 250 mm D 30 mm M, = 150 N.m 100 mm Find equivalent force-couple system at = 56.6 MPa center of transverse section passing through H. P = 600 N T = (600 NX0.45 m)= 270 Nm M, = (600 N)0.25 m)=150 Nm 50.9 MPa Try Find normal and shearing stresses at H. (150 Nm X0.015 m) +z (0.015m)" (270 Nm)X0.015 m) }7(0.015 m)" Mc 6, =+ Te =+ o, = +56.6 MPa T, = +50.9 MPa
If the wide flange is subjected to a shear force of V = 30 kN, Draw the shear stress distribution in the beam and identify the maximum shear stress tmax-. Set w 200 mm. 300 mm A 20 mm 20 mm V 400 mm 20 mm W-
Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 6 kN 10 kN 3 kN/m 2 kN 5 kN-m G 3000mm. 1000mm 1000mm. 2000mm. 1000mm. 2000mm. 3. Determine the shear ation for segment B-C. ** 4. Determine the moment equation of segment C-D.**