Ace.Ans1.33. Plot the kinematic viscosity of stcam at 300 psia for the range of temperature of steam properties in TaeB-4 (Engl.).Ans y 2.4814 x 1 s at 530 °F.p 0.5102 lb/ft' at 530°F134Durine lounch a NA

Given Pressure, P = 300 psia Find Kinematic viscosity

Answered: 1.33. Plot the kinematic viscosity of…

1.33. Plot the kinematic viscosity of steam at 300 psia for the range of temperature of steam properties in Table B4 (Engl.). Ans y 2.4814 x 10 1/s at 530 °F, p = 0.5102 lb /ft' at 530 °F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QI A ball made of INOX AISI 365 steel with density of 8.52 gricm3 was used to determine the viscosity of oil with specific gravity of 0.91. In the viscometer, the ball traveled 19 cm in 2.2 seconds. If the diameter of the ball is 2.95 mm, what is the viscosity of the oil in pa.s ? assume that water density is 1000 kg/m'.
The kinematic viscosity of liquid oil (10³) C.S (1 stoke =100 C.S) and relative density = 0.92. Find the viscosity of the fluid oil in c.g.s and SI %3D systems.
sF.r.cylinder.rsh Tcy are the radius of shaft and inside radius of cylinder a P2.11 Consider a concentric shaft fixed axially and rotated inside <( cylinder.r3h.ľcy are the radius of shaft and inside radius of cylinder respectively, with total length L. Let the rotational rate @ rad/s and applied torque be M .Using these parameters, a) Derive a theoretical relation for the viscosity u of the fluid between the shaft and cylinder. b) For a shaft of 8cm long, rotating at 1200 rev./min, with rsh = 2.00 cm and the measured torque is M viscosity? [µ = M(rcy=r sh)/(2nwr;,L)] %3D - 0.293 N.m. What is the fluid [µ=0.29 kg/m.s] rey:205 ( Cos o 6243.
The company has opted to purchase a new viscometer for you, as such, you are required by topropose two options for new viscometers. Select two viscometers and explain their operation andconstraints. (P3)b. (P4) Given that you achieved the following results with a U-Tube viscometer:Temperature/ C Time / s40 5760 4180 29100 16Calculate the viscosity at each temperature if the calibration constant is 0.511.d. (M2) Illustrate the results on a graph of temperature vs viscosity and give a briefing on what yourresults indicate, identifying the response of the oil to temperature and explaining anydiscrepancies that may have occurred during the testing.e. (D2) From your testing you discovered that you had a Newtonian and Non-Newtonian sample.Explain to your team what the two terms mean with respect to temperature and shear force onboth samples, giving at least one example of each type of fluid.
plz help me with this one , i would appreciate it if you can help me now. A piston with a diameter of 0.8 m and width of L=0.6 m rotates with 6 rad/s inside a cylinder that has a diameter of 1 m that filled with oil that has a viscosity of 8x10-3 N.s/m2 What is the shear force that acts on the circumference of the piston (N)? Assume the variation in velocity of the oil is linear.
YEUFAaA Tnd Natural Resources MECH 271 - Introduction to Fluid Mechanics Assignment 1- Pressure 1. The basic barometer ean be used to measure the height of a building If the barometrik readings at the top and at the bottom of a building are 730 mmHg and 755 mmlls respectively, determine the height of the building Assume an average ar density of 1.18 kg/m, 2. Agas is contained in a vertical, trictionless piston cylinder devie The piston hasa mass of 4 kg and a cross octonal area l35 cm A cumpressed spring above the oressure is SAP..
C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and specific gravity of 1.11. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3,(iii) the kinematic viscosity in stokes, and (iv) the specific volume in m³/kg. C1 (b). The capillary effect in a glass tube of 2.6 mm diameter, when immersed in (1) water and (2) mercury are 7.4 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a).(i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m³/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m
SAE 10W30 motor oil has a dynamic viscosity of 0.21 kilograms per meter second and a specific gravity of 0.896 (a) What is the density of the motor oil in units of kilograms per cubic meter?
C1 (a). A lubricating oil having the dynamic viscosity of 0.056 poise and specific gravity of 1.17. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (iii) the kinematic viscosity in stokes, and (iv) the specific volume in m3/kg. C1 (b). The capillary effect in a glass tube of 2.8 mm diameter, when immersed in (1) water and (2) mercury are 7.7 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a). (i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m3/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m
In the figure given, fluid 2 is carbon tetrachloride and fluid 1 is benzene. If patm = 101.5 kPa, determine the absolute pressure at point A. fluid 1 A T 12 cm Patm fluid 2 35 cm ] LIVE 10 nexxt Reimagine Education. www.dlsl.edu.ph
is called a cone-plate viscometer A solid cone of angle 2k, base 1, and density p, is rotat- Ing with initial angular velocity my inside a conical.seat, as shown in Fig. of viscosity u. Neglecting air drag, derive an analytical ex- pression for the cone's angular velocity ) if there is no applied tongue. The device in Fig. The angle of the cone is very small, so thiat sin 0 0, and the gap is filled with the test liquid. The torque M to rotate the cone at a rate 1 is measured. Assuming a lin- ear velocity profile in the fluid film, derive an expression for tiuid viscosity u as a tumction of (M, R. S2, 0). The clearance h is filled with nil Bave C co radius a dwit) dt Fluid I manmot 1Inentia Derive an expression for the capillary height change h for a fluid of surface tension Y and contact angle 0 between two vertical parallel plates a distance W apart, as in Fig. . What will li be for water at 20°C if W = 0.5 mm? A thin plate is separated from two fixed plates by very vis- cous liquids…
C1 (a). A lubricating oil having the dynamic viscosity of 0.057 poise and specific gravity of 1.1. Calculate () the density of oil in kg/m?, (i) the weight density of oil in N/m². ii) the kinematic viscosity in stokes, and (iv) the specific volume in m /kg. (4 Marks) C1 (b). The capillary effect in a glass tube of 2.1 mm diameter, when immersed in (1) water and (2) mercury are 8.5 mm and -2.8 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. (3 Marks) (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) C1(a).6).the density of oil in kg/m (1 Mark) C1(a). (i) the weight density of oil in N/m? (1 Mark) C1(a). (ii) the kinematic viscosity in stokes (1 Mark) C1a). (iv) the specific volume in m?/kg (1 Mark) C1 (b). 1.the value of surface tension (water) in N/m (1.5 Marks) C1 (b). 2. the value of surface tension…