Meter QuestionsThese questions address how to use and read the Simpson and Fluke DMM whenmeasuring resistance. You can get assistance by referring to the meter manualsincluded at the end of your course packet. If you have any questions, ask one of the Labstaff members.Simpson Model 260 Volt-Ohm-Milliammeter1.What are the three resistance ranges available on the Simpson meter?When changing resistance ranges on the Simpson meter, the meter must be zeroedusing the Zero Ohm's Adjust knob. What is/are the reason(s) for this step?2.3.Where is "OQ" on the meter scale – on the left or right end?a. Leftb. Right4.Is the Simpson meter more accurate at the left or right end of the OHMS scale?a. Leftb. RightC. The meter has the same accuracy across the entire OHMS scaleA meter is set to the "Rx100" setting and the needle is pointing to "200" on the OHMSscale. The technician changes to the Rx10,000 setting and the pointer settles over"1.8". Which is the more accurate reading?a. The Rx100 readingb. The Rx10,000 readingc. Either is fine. Neither one is more accurate than the other.5.0710 assign_ELTE108_Homework_07_2011-11-04ACC.docxPage 3 of 4

Simpson multi meter are used to measure the voltage current and resistance values. The following…

1. What are the three resistance ranges available on the Simpson meter? 2. When changing resistance ranges on the Simpson meter, the meter must be zeroed using the Zero Ohm's Adjust knob. What is/are the reason(s) for this step? 3. Where is "00" on the meter scale - on the left or right end? a. Left b. Right 4. Is the Simpson meter more accurate at the left or right end of the OHMS scale? a. Left b. Right c. The meter has the same accuracy across the entire OHMS scale 5. A meter is set to the "Rx100" setting and the needle is pointing to "200" on the OHMS scale. The technician changes to the Rx10,000 setting and the pointer settles over "1.8". Which is the more accurate reading? a. The Rx100 reading b. The Rx10,000 reading c. Either is fine. Neither one is more accurate than the other.

1. What are the three resistance ranges available on the Simpson meter? 2. When changing resistance ranges on the Simpson meter, the meter must be zeroed using the Zero Ohm's Adjust knob. What is/are the reason(s) for this step? 3. Where is "00" on the meter scale - on the left or right end? a. Left b. Right 4. Is the Simpson meter more accurate at the left or right end of the OHMS scale? a. Left b. Right c. The meter has the same accuracy across the entire OHMS scale 5. A meter is set to the "Rx100" setting and the needle is pointing to "200" on the OHMS scale. The technician changes to the Rx10,000 setting and the pointer settles over "1.8". Which is the more accurate reading? a. The Rx100 reading b. The Rx10,000 reading c. Either is fine. Neither one is more accurate than the other.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 14RQ: 14. A 6-V lead-acid battery has an A-hr rating of 180 A-hr. The battery is to be load-tested. What...

See similar textbooks

Similar questions

List 6 parts of Multimeter including each corresponding function.
A certain resistance was measured to be 30 ohm at 20°C and 40 ohm at 70°C. Find the temperature coefficient (in per °C ) at 0°C. (Use 4 decimal places. Unit is not required.)
If the measured values for resistors #1, #2 and # 3 are 552, 549 and 549 Ohms calculate the %error (measured difference from expected value as a percentage) for each resistor. Are they within tolerance (or specification) of manufacturer? #1 98.4% #2 97.9% #3 97.9% Yes within specification a. b. #1 1.6% #2 2.1% #3 2.1% Yes within specification #1 1.6% #2 2.1% #3 2.1% No outside specification Ос. Use Ohm's Law to calculate the equivalent resistance of R12, R23 and R123 (as specified in the lab manual) using measured resistances #1 552 Ohms, #2 549 Ohms, #3 549 Ohms R, R2 R,= R12 R23
Which of the following can cause corrosion to metal and is used to dissolve unnecessary copper in the base board of a circuit board? * O A. Copper layer O B. Etchant solution O c. Soldering iron O D. Soldering lead
Draw the block diagram of digital Multimeter and explain the measurement of D.C voltage
Where is the best place in a circuit to find absolute zero when measuring voltage? O At the negative terminal of the battery. O At the positive terminal of the battery. O At either side of the circuit protection device. O On the ground side of the load device. ore
A string insulator has 6 units. The voltage across the bottom most until is 20% of the total voltage. Its string efficiency is?
What is the purpose of shunt resistors in an ammeter? A. To shorten the range of the ammeter. B. To shunt current around the meter movement. C. To shunt voltage around the meter movement. D. To limit current at the input of the ammeter.
What is the word for meter measure
Give a detailed description of an expirment about 'D'Arsonval Meter Movement as DC ammeter'.Support your answer with pictures and examples.
Determine the CH2 peak value. Write the values only in four decimal places. the correct answer is 1.9600 please show the solution thank you!
leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potent the motor in that direction, causing the motor to spin. O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction. Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2. D2 Yellow R1 50 Q R2 50 0 R3 PSB (+ 5 V 100 aLW R4 D1 100 Q Blue SW1 Sw2 Question 2 本