Number 2 please 1. Using the circuit in Figure 1, determine the value of R₁. The power supplied by the 12V sourceto the entire circuit should be 72.6 mW. The power supplied by the 5V source to the entirecircuit should be 7.3 mW. Show your calculations in detail.RL=47012V820wwRLIL(12V source):IL(5V source):IL(total):www330wwwFigure 1: Superposition Circuit2205V2. Use the Superposition Theorem to determine the value of the current in R₁ from the 12V sourceand the current in R₁ from the 5V source. Show your calculations in detail.

Note: For the calculation of Question 2, we need the value of the resistance that can be calculated…

1. Using the circuit in Figure 1, determine the value of R₁. The power supplied by the 12V source to the entire circuit should be 72.6 mW. The power supplied by the 5V source to the entire circuit should be 7.3 mW. Show your calculations in detail. RL = 470 12V 820 RL IL(12V source):_ IL(5V source): IL(total): 330 Www Figure 1: Superposition Circuit 220 5V 2. Use the Superposition Theorem to determine the value of the current in R₁ from the 12V source and the current in R₁ from the 5V source. Show your calculations in detail.

1. Using the circuit in Figure 1, determine the value of R₁. The power supplied by the 12V source to the entire circuit should be 72.6 mW. The power supplied by the 5V source to the entire circuit should be 7.3 mW. Show your calculations in detail. RL = 470 12V 820 RL IL(12V source):_ IL(5V source): IL(total): 330 Www Figure 1: Superposition Circuit 220 5V 2. Use the Superposition Theorem to determine the value of the current in R₁ from the 12V source and the current in R₁ from the 5V source. Show your calculations in detail.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
Determine the DC currents (la. lc and I) and dc junction voltages (Var Ver and Vca) la-Blank 1 mA, le-Blank 2 mA, I-Blank 3 mA, Var Blank 4 V, Vcr Blank 5 V and VcB - Blank 6 V Use 2 decimal places. Use the following values. VBB= 3V RB= 5kOhms Rc=232 ohms Vcc =18 V BDC=65
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor.
Which methods can be used to estimate or calculate the maximum power point on an I-V curve?
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10
If T = 0.6Z – 60° and A = 48cm find the position of the first voltage minimum on the line. Select one: O a. The first voltage minimum is at 2cm from the load. O b. The first voltage minimum is at 72cm from the load. O c. The first voltage minimum is at 8cm from the load. O d. The first voltage minimum is at –4cm from the load. O e. The first voltage minimum is at 20cm from the load. O f. The first voltage minimum is at 32cm from the load. O g. The first voltage minimum is at 44cm from the load. O h. The first voltage minimum is at 24cm from the load.
In the figure: R1 = 1439.170, R2 = R1 and R3 =2R2, then determine the value of the voltage source E. a 8 mA 10 mA 2 mA RT R1 R2 R3 O 25.33 11.51 O 17.27 15.43 13.82 +
Series-Parallel Circuit For the following circuit, determine: a) The total resistance RT b) The current IRI c) The current Ir6. d) The power consumed by R6.. . Ri 15 Ry 30s 15L 15 Rz 12v 30s2
In the figure: R1 = 27.3 Q, R2 = 93.1 Q and R3 = 1571.12 Q, then determine the value of the source current Is. 12 13 RT R1 R2 R3 E 1.33 0.98 1.44 1.73 1.15
If the voltage V, = 800 mV, then the current flowing in the load I, is: %3D -j20n Select one: O a. None of these O b. Is 100 <-90° mA O c. Is 5.0<.-90° A O d. Is 5 <90° mA ell
Determine the DC currents (IB, Ic and lĘ) and dc junction voltages (VBE, VCE and VCB) Ig=Blank 1 mA, Ic=Blank 2 mA, IĘ=Blank 3 mA, VBE= Blank 4 V, VCE = Blank 5 V and VCB = Blank 6 V Use 2 decimal places. Use the following values: VBB = 2V RB = 7 kQ Rc = 248 Q Vcc = 19 V BDc = 56 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer Blank 4 Add your answer Blank 5 Add your answer Blank 6 Add your answer