1. The beam is made up of the wood section that is glued together as shown. If the allowable stress is Tallow = 800 psi and each glued joint can withstand 260 lb/in., (a) determine the largest allowable distributed loading w that can be applied to the beam. (b) If w = 260 lb/ft, determine the shear flow that must be resisted by each glued joint. The beam dimension are as follows; a = 4 in., b = 3 in., c = 6 in., d = 3in., and e = 3 in.

1. The beam is made up of the wood section that is glued together as shown. If the allowable stress is Tallow = 800 psi and each glued joint can withstand 260 lb/in., (a) determine the largest allowable distributed loading w that can be applied to the beam. (b) If w = 260 lb/ft, determine the shear flow that must be resisted by each glued joint. The beam dimension are as follows; a = 4 in., b = 3 in., c = 6 in., d = 3in., and e = 3 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam carrying an allowable actual moment of -38 KN- m is reinforced as shown. If the the concrete is normal weight and f'c = 25MPa and fy = 420MPa. Determine the following: a. The cracking moment of the beam. b. The transformed moment of Inertia. c. The actual tension steel stress. d. Check the stress if it is correct by force checks. mm www.009 4-020 О 140 mm 300 mm 170 mm * 170 mm: ww.08 ✓ 60 mm
Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P P₂ B C D +250 -350 mm 500 mm A -250 mm- ANSWER: KN, PBC = PCD = KN KN, PAB = (express it in whole number)
Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² Pr B C D 500 mm -250 250 mm 350 mm- ANSWER: KN, PBC = PCD = KN KN, PAB= (express it in whole number) A
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPA, f, = 280MPA and the net tensile strain is greater than 0.005, then the maximum steel ratio equals. . (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm
Two wooden members, each having a width of b = 6.6 in. and a depth of d = 2.2 in., are joined by a simple glued scarf joint. Assume ß= 30°. If the allowable shear stress for the glue used in the joint is 108 psi, what is the largest axial load P that may be applied? P P Answer: P = i lb
A beam, which is rectangular, has a base of 250 mm, and d = 575 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given a) Determine the value of "a".
The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.
Part A The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown. Epr = 100 GPa, Est = 200 GPa. The allowable bending stress for the steel is (oallow)st = 180 MPa, and for the brass (oallow )br = 54 MPa . (Figure 1) Determine the maximum moment M that can be applied to the beam. Express your answer to three significant figures and include the appropriate units. HA ? M = 111.01 kN • m Figure < 1 of 1 Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining 50 mm Provide Feedback 200 mm B M 175 mm
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 15 kips, w = 4.0 kips/ft, LAB = 3.2 ft, LBC= 3.2 ft, and LcD = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. P LAB Answer: Omax B LBC ↓↓↓ C ksi W LCD X
Can you help me with this please show the clear complete solution and fbd Given: W = 600 lb Tension at AB, AC and AD