1. Find the equivalent transfer function of the negative feedback system shown inR(s)C(s)Ks(s+2)²1Find values of gain K that will yield closed-loop poles that ensure (a) an overdampedresponse, (b) an under-damped response, (iii) a critically damped response. Showthe pole locations for each case in a rough graph mentioning the corresponding valueof K.Find a value of the gain K that will make the system marginally stable.Find the associated frequency of oscillation. show the pole locations for each case ina rough graph mentioning the corresponding value of K.

The negative feedback system is shown in figure The open-loop transfer function is G(s)=Ks(s+2)2…

Answered: 1. Find the equivalent transfer…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

For the given four statements below, which of the following are not correct about an op-amp with negative feedback arrangement? i. Negative feedback reduces the gain of the op-amp circuit to desired value. ii. Negative feedback takes portion of the output and applies it back in-phase with the input. iii. Negative feedback controls the voltage transfer characteristic of the op-amp circuit. iv. Negative feedback maintains the oscillations. i and ii O i and iv iii and iv O i and iii
Given the feedback circuit below and assuming the voltage amplifier has gain A₂, input resistance R₁ and output resistance Ro, answer the following questions: + a. Loop gain b. Closed loop gain Re C. Input resistance d. Output resistance Rin м + RE A) Sketch the feedback small signal model of this circuit. (Hint: You may convert the input VIN and source resistance Rs to its Norton current equivalent if needed) B) Find the following in terms of the amplifier parameters and resistances R, and RF: Rout
Homework2:)A feedback system employing output rate damping is shown in Figure below. A. Find the values of K1 and K2 so that the closed-loop system resembles a second- order system with damping ratio equal to 0.5 and frequency of damped oscillations 9.5 rad/sec. B. With the above values of K1 and K2, find the percentage overshoot when input is step input. C. What is the settling time for 2 percent tolerance? 14 Scanned with CamScanner Computer Technology Eng. Dept. Control Engineering Fundamentals Third Class R(s) > Ki C(s) sCI+s) Answer: K=120.34 K2-9.97 Mp=16.31% t=0.729 sec
a- Zero. b- Slightly different from zero. O Maximum positive or negative. d- An amplified sin wave. 9-Negative feedback reduces @ The feedback fraction. b- Distortion. c- The input offset voltage. d- The open-loop gain. 10-The input impedance of a current-voltage converter is Small. b- Large. c- Ideally zero. d- Ideally infinite. a- 11-In a linear op-amp circuit, the @ Signal are always sin wave. b- Op-amp does not go into saturation. c- Input impedance is ideally infinite. d- Gain-bandwidth product is constant.
Consider the series-shunt feedback amplifier of Figure below. Assume that the voltage divider (R1, R2) is implemented with a 1-MQ potentiometer. Assume that the MOSFET is biased so that gm 4 mA/V and r, is large. Also, Rp = 10 k. A VDD Find the value of R1 that results in a closed-loop gain of 5 V/V. Rp R2 R1 V,
Given the following values and shunt-series feedback circuit below, answer the following question: The open-loop gain of the circuit is: A. 7.5 S B. -17850 C. 28125 D. −70312500 Ω
In the opamp circuit, the value of the gain should be 10, what is the value of the resistor to be used as feedback resistance? Find the equation statement that gives the output. Find Rf.
Q1: design an inverting op-amp circuit to form the weighted sum Vo = -(v1 + 4v2) .choose the values for R1, R2, and Rf so that for a maximum output voltage of 10 volt the current in the feedback resistor will not exceed 1 ma.
Q2: For the unity feedback second order system shown below, if R(s) is a unit step, trace R(s), E(s) and C(s). Take a. K=50 and kl=10 b. K=k1=10 c. K=25 and kl=10. Comment on the results in each case. R(s) E(s) K. C(s) (s +. kl)s
Assume for a moment that perfectly accurate resistors were available for feedback networks; that is resistor tolerance is 0%. Then any deviation from the value set by the feedback resistor ratio is caused by insufficient raw op-amp gain. What minimum raw gain would be needed to get within 1% if an intended overall gain of 10? What if the intended gain is 100 instead?
Given the feedback circuit below: V, 0- RE Rei m Q₁ a Vcc 2₂ m Rc₂ RF Q3 -o V₂ Find the following in terms of the BJT parameters and resistances RE and RF: a. Loop gain b. Closed loop gain c. Input resistance d. Output resistance Note: Assume that B = ∞ and V₂ = ∞ for all BJTS and the current source is ideal.
An uncompensated system shown in Figure 3(a) has forward transfer function G(s) with a unity feedback. Summarize the various performance parameters in tabular form and comment on the design results. Mention about the speed of response and stability.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning