1. Describe how would you use a multimeter to test each of the following. Describe where you would place the 2 probes, and which dial setting in the multimeter you would use. a.) check if a battery has low voltage i. b.) how much current is flowing at a certain point in a circuit 2. Describe 2 ways that multimeters are commonly 'burnt' (destroyed): ii. c.) check if the cable between your electric-guitar and an amplifier is broken under the insulation

1. Describe how would you use a multimeter to test each of the following. Describe where you would place the 2 probes, and which dial setting in the multimeter you would use. a.) check if a battery has low voltage i. b.) how much current is flowing at a certain point in a circuit 2. Describe 2 ways that multimeters are commonly 'burnt' (destroyed): ii. c.) check if the cable between your electric-guitar and an amplifier is broken under the insulation

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Give a detailed description of an expirment about 'D'Arsonval Meter Movement as DC ammeter'.Support your answer with pictures and examples.
What are the relationships of resistance, voltage and current, and the distribution of voltages and currents in each resistor for the different type of circuits.
Q1.) a) PMMC meter has (10mA) half scale current deflection and (1500) internal resistance. Use this meter to design a dc multimeter of indirect ammeter and direct voltmeter methods to measure the following ranges of current and voltage: 50mA, 100mA, 1A, 5V, 50V, and 150V. Draw the circuit diagram of this multimeter with a control switch that can be used to measure either current or voltage.
1. The practical unit of electric charge. 2. A path for the current to flow. 3. DC Voltage has 4. Resistance to current flow in AC circuits, measured in ohms. 5-7. Types of grounds in electrical circuits. 8. Also known as Ohm's Law. 9. A quantity defined as amount of work done over time. 10. Types of material that has 4 valence electrons. 11. One Coulomb is equal to 12. Best conductor material type. 13. Best insulator material type. 14.The value of a resistor without considering its tolerance value percentages. 15. 1 picoampere (pA) is equal to -polarity electrons or protons stored in a dielectric. ampere (A).
Make three plots using Excel: 1. Voltage vs current for the linear resistor data (voltage on vertical axis, current on horizontal). Add a linear trendline with the equation and R² value shown. 2. Voltage vs current for the lightbulb data (voltage on vertical axis, current on horizontal). 3. A plot showing both curves on the same set of axes (voltage on vertical axis, current on horizontal).
what is the causes of voltage drop
How can you use a DMM to measure different characteristics of electrical components and circuits? Why are these measurements important?
State the characteristics of voltage and current in a series circuit connection of resistors. State the characteristics of voltage and current in a parallel circuit connection of resistors. please explain it properly.
14. A DC ammeter set at 2 mA range is connected in series with the lamp. What is the current reading? Assume the lamp has a resistance of 10 ohms.
2. What is the significance of negative values of voltages and current?
4. Four cells each of 2.10 volt internal emf are parallel connected together to make a battery. The internal resistances are 0.004, 0.005, 0.003 and 0.0025 ohm. Calculate for parallel connections: (a) internal emf and resistance of the single equivalent cell (b) current for a terminal voltage of 1.95 volts, (c)current in each cell
What are the differences between load resistance in a circuit and internal resistance in a battery? Explain.