1. An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 1 mm horizontally when it is subjected to a horizontal force P = 2 kN, determine the shear modulus of the polymer. The width of the block is 100 mm. Assume that the polymer is linearly elastic and use small angle analysis. 200 mm 400 mm P = 2 kN

1. An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 1 mm horizontally when it is subjected to a horizontal force P = 2 kN, determine the shear modulus of the polymer. The width of the block is 100 mm. Assume that the polymer is linearly elastic and use small angle analysis. 200 mm 400 mm P = 2 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thank you for answering this question. Please you specify each step as soon as possible. Good Luck! Thank You. Consider a 60-mm cube made of graphite-reinforced polymer composite material that is subjected to a tensile force of 100 kN perpendicular to the fiber direction, directed along the 2-direction. The cube is free to expand or contract. Determine the strains (Ɛ11; E22, Ɛ33, Y23, Y31. Y12) using following material constants for graphite-reinforced polymer composite. E1 =155 GPa, E2 = E3 = 12.10 GPa U 23 = 0.458, D12 =V13 = 0.248 G23 = 3.20 GPa, G12 = G13 = 4.40 GPa
An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 2 mm horizontally when it is subjected to a horizontal force P = 2 kN, determine the shear modulus of the polymer. The width of the block is 100 mm. Assume that the polymer is linearly elastic and use small-angle analysis.
A band of polymer is to hold together a bundle of steel rods for up to one year. if the stress on the band is less than 1300 psi, the band will not hold the rods tightly. determine the initial stress that must be applied to the polymer band when it is slipped over the steel. A series of tests showed that an initial stress of 1000 psi decreased to 980 psi after 5 days. (1yr. = 12 mos = 52wks)
You must perform mechanical tests with a linear elastic material (the material follows Hooke's law) applying forces (tension) in the range 0 to Fmax/2 for Sample A and between 0 to Fmax for Sample B. The samples are made of same material but have different geometries (see illustration). (a) Which of the two samples receives the maximum stress (σmax)? (b) Which of the two samples will have the larger length change (ΔLmax)? (c) Plot the expected curves for the two samples in the force-length and stress-strain planes. (d) Clearly indicate the values that the variables force, length, stress, and strain take at the beginning and end of each curve.
Find the breaking point along the fishing rod assuming that the base of the rod is in a fixed position and will not move. The rod is made out of Carbon fiber with diameters a=9.93 mm wide, b=7.13mm wide, and c=5.1mm wide. The total length of the rod is 2 meters. The modulus of elasticity of Carbon Fiber is 228 Gpa. Find what force "F" is needed to break the fishing rod assuming that the force is acting straight along the line. | 100 45 F
A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’s ratio of 0.35 is subjected to tension within the elastic region. Determine the force ( in N) that will produce a reduction of 0.003 mm in the diameter.
Natural rubber is tested in tension to a maximum extension ratio of λ = 3. The Mooney-Rivlin constants for this material are found to be C1 = 0.069 MPa and C2 = 0.125 MPa. Plot the corresponding uniaxial stress vs. extension ratio behavior over the tested range. Derive an expression for the slope of the function, then determine the secant and tangent moduli at 100% strain.
Determine the change in length, width and thickness of steel bar which is 4m long, 30mm wide and 20mm thick and is subjected to an axial pull of 30 kN in the direction of length. Take E = 200 GPa and poison's ratio of 0.3. Also determine the volumetric strain and change in volume.
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 9 mm & Modulus of Elasticity 201 GPa. It is found that the specimen has undergone an extension of 1 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain- induced due to the load "F" on the specimen is 3.6 x 10-³. Solution Cross-sectional Area, A (in mm²) = 63.617 One possible correct answer is: 63.617251235193 Tensile Stress, (in N/mm²) 723.6 One possible correct answer is: 723.6 Tensile Load, (in N) = = 46033.261 One possible correct answer is: 46033.442993786 Length of the Specimen (in mm) 4.366 X One possible correct answer is: 277.77777777778
The piece of plastic is originally rectangular. Suppose that aaa = 270 mmmm and bbb = 440 mmmm . (Figure 1) Figure 1 of 1 Part A Determine the magnitude of the shear strain γxyγxy at corner DD if the plastic distorts as shown by the dashed lines
A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’s ratio of 0.35 is subjected to tension within the elastic region. Determine the force ( in N) that will produce a reduction of 0.003 mm in the diameter. I The answer is supposed to be 14,063 but im getting something else. Can you show how its supposed to be 14,063