1. A three-phase delta-connected load of 15+ j18 Q per phase is supplied by an abc-sequence balanced three-phasewye-connected source with a line voltage of 400 V. The line impedance is 1 + j20 per phase. Taking Ea as reference,determine the line currents, phase load currents, phase load voltages, and the total complex power supplied by theSource.

In this question, We need to determine the phase current, line current phase load voltage and…

1. A three-phase delta-connected load of 15+ j18 N per phase is supplied by an abc-sequence balanced three-phase wye-connected source with a line voltage of 400 V. The line impedance is 1 + j2 Q per phase. Taking Ea as reference, determine the line currents, phase load currents, phase load voltages, and the total complex power supplied by the Source.

1. A three-phase delta-connected load of 15+ j18 N per phase is supplied by an abc-sequence balanced three-phase wye-connected source with a line voltage of 400 V. The line impedance is 1 + j2 Q per phase. Taking Ea as reference, determine the line currents, phase load currents, phase load voltages, and the total complex power supplied by the Source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.52P: A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated...

See similar textbooks

Similar questions

The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line voltages are 3 times the line-to-neutral voltages and lend by 30. (a) True (b) False
An unbalanced three-phase wye-connected and grounded load is connected to a balanced three- phase four-wire source. The load impedances Z, Z, and Z, are given as 70 230°, 85 L-40°, and 50 235° 2/phase, respectively, and the phase a line voltage has an effective value of 13.8 kV: use the line-to-neutral voltage of phase a as the reference and determine the following: The line and neutral currents. 113.823 L-450 93.737 L-000 150.353 L-2700 113.823 L-60° 93.737 L-000 159.353 L-2850 113.823 L-300 93.737 L-800 150.353 L-275o None
3 phase balanced Wye connected inductive loads have PLOAD When connected to VGEN three phase generator as shown in figure below. In this figure Van is reference voltage. (Generator internal resistance and line impedance are neglected. PLOAD and Van values are given in Table1.) a. Calculate the line currents (laA,IbB,and IcC) b. Calculate the line voltages (Vab,Vbc,and Vca) A N IbB b
An unbalanced three-phase wye-connected and grounded load is connected to a balanced three- phase four-wire source. The load impedances Z, Z,, and Z, are given as 70 230°, 85L-40°, and 50 235° 2/phase, respectively, and the phase a line voltage has an effective value of 13.8 kV: use the line-to-neutral voltage of phase a as the reference and determine the following: The total power aelivered to the loads. 1025.795 kW 1035.795 kW 1055.795 kW None
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
4) A balanced delta connected load of ...+j18 ohm per phase is connected at the end of a three phase line as shown in figure. The line impedance is 1+j2 ohm per phase. The line is supplied from a three-phase source with a lie- to-line voltage of 207.85 V rms. Taking Van as reference, determine the following: a) Current in phase a. b) Total complex power supplied from the source. c) Magnitude of the line-to-line voltage at the load terminal. (Please determine the impedance value within the specified limits: 16-26 V. By considering the impedance value you determined yourself, solve the question.) ao- |V₂| bo Co- 1 +j2 Ω = 207.85 V www Figure a Jum ...+j18 n b
1. Calculate the line currents for phase a, b and c.2. Calculate the line-to-neutral voltages at the load for phase a, b and c.3. Draw the phasor diagram of the source line-to-neutral voltages and line currents.
The currents flowing in the lines toward a balanced load connected in A are Ia 10020° A, Ib 141.4225° A, and I. = 100290° A. Look for the following: a.Find the symmetrical components of the given line currents b.Draw the phasor diagram of the positive sequence currents of the line currents c. Draw the phasor diagram of the negative sequence currents of the line currents d.What is Iab?'
2. A three-phase transmission line has parameters Xc-6 k 2, R-3.25 2 and X₁-25 92, and delivers 300 MW to a load with both ends of the line at 230 kV. Draw a pi equivalent per-phase circuit of the line. On a per-phase basis, calculate the active power delivered to the load, the reactive power of the line and the active power delivered by the source. Based on these calculations can the equivalent circuit be simplified further?
A balanced delta connected load of 14+j16 ohm per phase is connected at the end of three phase line. The line impedance is 4+j6 per phase . The line is supplied from athree source with a line to line voltage of 207.85 Vrms. Tnaking phase voltage Va as reference determine the following: a) I in phase a b) Total complex power supplied from the source c) Magnitude of the line to line voltage at the load terminal.