1. A massless wire connects two masses, one of which is exactly twice the other. If the connecting wire has length L, should a support be placed at a distance L/3 from the larger mass to achieve equilibrium? The mass of the wire is assumed to be negligible. 2. Are projectiles subject to constant acceleration in two dimensions? 3. Explain in detail why a spinning ice-skater's angular speed increases when she pulls in her arms closer to her body. 4. Stand facing the edge of an open door, one foot on each side of the door. You will find that you are not able to stand on your toes. Why? 5. Two identical pool balls are shot directly at one another at the same speed. Describe the ball's motions after they collide, assuming that frictional forces may be neglected and the collision is completely elastic.

1. A massless wire connects two masses, one of which is exactly twice the other. If the connecting wire has length L, should a support be placed at a distance L/3 from the larger mass to achieve equilibrium? The mass of the wire is assumed to be negligible. 2. Are projectiles subject to constant acceleration in two dimensions? 3. Explain in detail why a spinning ice-skater's angular speed increases when she pulls in her arms closer to her body. 4. Stand facing the edge of an open door, one foot on each side of the door. You will find that you are not able to stand on your toes. Why? 5. Two identical pool balls are shot directly at one another at the same speed. Describe the ball's motions after they collide, assuming that frictional forces may be neglected and the collision is completely elastic.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 12.52AP

See similar textbooks

Similar questions

5. In the figure shown, a uniform bar has its center of gravity at C and weighs 350 N. A. Draw the FBD and show all the forces acting on the bar. B. Determine the tension on the cable. C. Determine the reactions at A and B. Assume that the surfaces are smooth. 45° 350 N cable B 2 m → 4 m * 2 m
1. A uniform pole 20 ft long and weighing 80 lbs is carried by two men A and B, one at each end of the pole. a. Draw the figure b. Draw the force diagram c. Write the equations for the 1st Condition and for the 2nd Condition of equilibrium
a. What are the conditions for static equilibrium? b. A 30.0 kg post is supported by two wires as shown. The post is 2.00 m long and a 5.00 kg wreath hangs 1.50 m from one end. Use the conditions for static equilibrium from part (a) to find the tension in each wire. Include a free body diagram as part of your answer.
1. Problem No. 1: A series of cables are connected to a ring at B and D, as shown in the figure. For this system: a) Draw the FBD of point D. b) Determine the force in cable DB and cable DE. A B 100 lb. 15° 80 lb. 45° E
2. A strain gauge (see picture shown below from Omega) is a resistance element that is used to measure the fractional elongation experienced by a material. If it is attached to a beam that undergoes a deflection due to an impact, we can use the gauge to measure the deflection or monitor the frequency with which the beam vibrates. R1 SG1 wwwwww Lumin Assume we attach two strain gauges (SG1 and SG2) on opposite sides of the beam as shown above. If the beam deflects downward, SG1 elongates (so its resistance increases) while SG2 compresses (so its resistance decreases). Let's hook up the elements into a Wheatstone bridge as shown below. If R1=R2=100 92, and the nominal values of SG1 and SG2 when no strain is present are 100 as well, what is the value of Vout when the beam is deflected enough to cause SG1 to increase to 100.1 № and SG2 to decrease to 99.9 N? The voltage at the top of the bridge (10V in this case) is called the "excitation voltage". 10V Vout R2 Wall SG2 SG 1 SG 2 Beam
cable 8. A 20 kg uniform beam 10m long is attached to a wall with a cable. The 40.0° cable is attached to the middle of the beam at 90° to the beam. A box box of mass 50 kg is suspended from the beam as shown. 50 0° a. Draw a free body diagram labelling all the forces acting on the beam (include the forces acting on the floor hinge). Choose and label an appropriate pivot point "P". Label all distances from this point. b. Determine the tension in the cable. с. Determine the force acting on the hinge at the bottom.
An outdoor chair is suspended from a tree by a single cable of length 1.5 m. The mass of the chair and the person sitting in it is a total of 85 kg. If someone pulls the chair through a horizontal distance of 80 cm and holds it there: a. What is the increase in the force exerted by the cable? b. How much sideways force must be exerted to hold the chair at that location?
A 4-m long, 150-kg steel beam is attached to a wall with one end connected to a hinge that allows the beam to rotate up and down. The other end of the beam is held in a horizontal position with a cable that makes a 27° angle with the beam and is attached to the wall (see (Figure 1)). a.What is the tension force that keeps this beam in static equilibrium? b. A mass of 75 kg is hung from the beam 3 meters away from the hinge (see (Figure 2)). Now what is the tension force that keeps this beam in static equilibrium? c.What is the vertical component of the force that the hinge exerts on the beam?
Determine the forces in cables AC and AB needed to hold the 30-kg cylinder D in equilibrium as shown in (Figure 1). Set F = 450 N and d = 1 m. Figure 1.5 m d -2 m- A D 1 of 1 Part A Determine FAC Express your answer to three significant figures and include the appropriate units. FAC = Submit Part B FAB = Submit μА Value Request Answer Determine FAB. Express your answer to three significant figures and include the appropriate units. LO ΜΑ Value Units Request Answer ? Units ?
2. A 50 kg Cylinder is hanging by the cables from the ceiling. Determine the magnitude of tensions in cables AB, AC and AD. You must solve this problem using statics method. Assume the value of g is 9.80. (-2,0,-2) m (-3,0,3) m (4, 0, 1 ) m A(0.-4, 0) mn 50 kg
With regard to mechanical equilibrium with respect to forces and torques: A. Net Forces and Net Torques cannot be positive. B. The Net force and Net Torque vanish for at least one system components. C. Net forces or net torques vanish for all system components. D. Net forces and net torques vanish for all system components.
X Incorrect The 55-kg cylinder is suspended from a clamping collar at Cwhich can be positioned at any horizontal position x between the fixed supports at A and B. The cable is 14 m in length. Determine and plot the tensions in cable segments AC and BC as a function of x over the interval 0