1. A fluid is flowing in a 6in diameter pipe at a pressure of 4PSI with a velocity of 8ft/s. The elevation of the center of the pipe above a given datum is 10 ft. Find the total energy head above the given datum in METERS if the fluid is Water Oil with specific gravity of 0.85 Gas with specific weight of 0.42 lb/ft³

1. A fluid is flowing in a 6in diameter pipe at a pressure of 4PSI with a velocity of 8ft/s. The elevation of the center of the pipe above a given datum is 10 ft. Find the total energy head above the given datum in METERS if the fluid is Water Oil with specific gravity of 0.85 Gas with specific weight of 0.42 lb/ft³

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A centrifugal pump is required to handle 50 lit/sec of gasoline against a net pressure of 4 kg/cm'. Determine the head in m of liquid and the HP required by the pump, if its overall efficiency is 62%. Take the specific gravity of gasoline as 0.7. (57 and 43) A centrifugal pump draws water from a sump through a vertical 15 cm pipe. The 3.5 m above water level in the sump. While pumping 35 lit/sec, gauges near the pump at entrance and discharge read 0.35 kg/cm and+1.8 kg/cm respectively. The discharge gauge is 0.5 m above the suction gauge. Determine the horsepower output of the pump. pump has a horizontal discharge pipe 10 cm diameter which is (10.82) To p. edict the performance of a loge centrifugal pump, its model, having the following specification, was made: P = 24 IIP H=8 m N=925 rpm Diameter of model pump impeller is 9 times smaller than that of the prototype. The prototype pump has to work against a head of 30 m. Find its working speed and HP required to drive it. Determine also…
0,5 Water flows from a tank of large cross-sectional area through a pipe as shown. The cross-sectional area of the pipe ab is 2.104 m and that of the pipe be is 1.104 m². The tank is filled to a height 0,5 m above the level of bc. Calculate the volume flow rate and the height h to which the water level rises in the vertical tube.
1. The discharge flowing down the pipe is 0.03 m³/s and the pressure at 2 is 0.14 kg/cm² greater than at 1. Assuming the losses in the pipe between 1 and 2 is k. Liquid flowing in the pipe is water. kv2 2g' find the value of 20 cm dia 10 cm dia mercury 3 m
A circular vessel 2m in diameter and 3m high is one-third filled with liquid A having s.g. of 1.0, one-third filled with liquid B having an s.g. of 2, and the remaining one-third filled with liquid C having an s.g. of 3. At the bottom of the vessel is a 900cm^2 standard circular. Find the time in seconds to empty the vessel through the orifice.
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. ( WITH FREE BODY DIAGRAM ) CHOIECES: A.2.56 B.-2.72 m C.12.74 m D.-4.67 m
A company needs to pump coconut oil (den: 924 kg/m^3) from the import truck to its holding tank 15 meters above the ground. If the pump that is used is able to create 2 ATM of pressure, what will be the velocity of the oil as it enters the tank?
The power 395 W is required to transmit 5 x 10-3 m3/s of water. Find the loss of head due to friction in a pipe. The head loss due to friction (in m of water) Answer
В4. An orifice meter with orifice area 945 mm2 is inserted in a pipe of area 1890 mm2 The pressure gauges fitted upstream and downstream of the orifice meter gives readings of 245 N/cm2 and 85 N/cm2 respectively. Co-efficient of discharge for the orifice meter is given as 0.54. Find the discharge of water through pipe. Head of water (in m) The discharge of water through pipe (in Litres/sec)
Water is flowing at the rate of 1.676 m/s in a 3.068 inches’ diameter horizontal pipe at apressure p1 of 68.9 kPa. It then passes to a pipe having an inside diameter of 2.067 inch. Thedensity of the water is 998 kg/m3.a) Calculate the new pressure p2 in the 2.067inch pipe. Assume no friction losses.b) If the piping is vertical and the flow is upward, calculate the new pressure p2. The pressure tap for p2 is 0.457 m above the tap for p1.c) Compare and discuss your answers in 2 (a) and 2(b).
= constant Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. Z شكر الكائر 2B ADA=400 mm PA 29.43 N/cm #28 m ZA 28 Dg= 400 mm Pe = 22.563 N/cm ZB = 30 m DATUM LINE
Water flows inside a horizontal pipe so that at the beginning of the pipe it’s velocity v1 is lower than the velocity at the end of the pipe v2. Compare the pressures at the beginning P1 and at the end of the pipe P2: A. P1 > P2 B. Not enough information
1- A 2 m long conical tube is fixed vertically with its smaller end upwards. It carries liquid in downward direction. The flow velocities at the smaller and larger ends are 5m/s and 2m/s respectively. The 0.35(u₁-u₂)² pressure head at the smaller end is 2.5 m of liquid. If the loss of head in the tube is 2g (u, and u₂ being the velocities at the smaller and larger ends respectively). Calculate the pressure head at the larger end.