1) The hotter fluid of a parallel flow heat exchanger decreases in temperature from 200°C to 100°C and the cooler fluid increases from 40°C to 90°C. For the same heat transfer, what is the percentage saving in area made by using counter flow instead? [34.5%]
Q: The pulley system shown is at rest when the motor M starts pulling in rope so as to lift the 120lb…
A: Given:The value of The weight of the cargo, The speed of cargo after ,
Q: +x 5. Sketch within a cubic unit cell the for no eod il vadiailw snimmabag 3ככ פר (a) (011). (e)…
A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…
Q: Water stored in a large, well-insulated storage tank at 210C, an from this tank by a pump at the…
A:
Q: A diffuse surface is characterized by the spectral hemispherical emissivity distribution shown in…
A: Given:The surface temperature
Q: A sign ABCD is constructed from 7 mm thick plate steel (density p=8000 kg/m³) with the geometry…
A: To find:Determine the reaction forces at A and E. Given data:A sign ABCD is constructed from a steel…
Q: Q1. Two bars AB and BC are linked at B as shown in Fig. Q1. The end A of bar AB is free to rotate…
A: I have write the answer belowExplanation:Let calculating Restoring torque due to torsional spring.…
Q: 2. A soccer player is kicking a ball. At the specific instant in time, the following information is…
A:
Q: Express the 40 lb force in the rope from point A to point C in cartesian format. Point C is in the…
A: Express the 40 lb force in the rope from point A to point C in cartesian format. Point C is in the…
Q: The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a)…
A: The maximum tensile bending stress is
Q: A train at a constant 58.0 km/h moves east for 24.0 min, then in a direction 49.0° east of due north…
A:
Q: A CO2 fire extinguisher is pressurized to 5.9 MPa. It is released into the environment to put out a…
A: To determine:the temperature of CO2 after the opened valve
Q: 2. (pp11-2p151gutay) - Give reasons for the adoption of the modified Rankine cycle. Steam is…
A: Several factors lead to the adoption of the modified Rankine cycle, including:Enhanced efficiency:…
Q: For the following mechanism, Given: . • Lengths: O₂A=4 in., O;B-8 in, BC=5 in., O₂O3-4 in. and…
A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…
Q: Find a "flat" object in your house, make necessary measurements, and then calculate the center of…
A:
Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…
A:
Q: Explain the results of the assessment using the time graph and at least three of the measurements…
A: Based on the provided time graph and the measurements collected, we can assess the results as…
Q: Consider the pin jointed frame depicted in the accompanying figure and determine the magnitude of…
A: The moment acting,
Q: Compute the coordinates of the centroid (x, y) of the shown. Hint: Use composite with shapes in the…
A:
Q: A rigid ball of weight 100 N is suspended with the help of a string. The ball is pulled by a…
A: Given data:Weight of the ball, W = 100 N.Draw the labeled diagram for the system,Apply Lami's…
Q: A single cylinder double acting pump has a cylinder diameter of 135 mm and a stroke of 270 mm. The…
A:
Q: (a) derive equations for the shear force V and the bending moment M for any location in the beam.…
A: (a) derive equations for the shear force V and the bending moment M for any location in the beam.…
Q: Q1: A refrigerator operates on an ideal vapor compression refrigeration cycle ( with R-134 a) as a…
A:
Q: Q4) Determine the velocity of cart A if cylinder B has a downward velocity of 2 m/sec at the instant…
A:
Q: The two blocks A and B each have a mass of 400 g. The blocks are fixed to the horizontal rods, and…
A: M=(2t+sin(at) ) N.ma= 5 rad/secV1 = 2 m/sm = 0.4 kgt= 3 secV2=?
Q: +0.040 Holes of diameter 25.0+0.020 mm are assembled interchangeably with the pins of diameter…
A: Basic size of hole and shaft =25mmUpper limit of hole =25+0.040=25.040mmLower limit of hole…
Q: 7. A solid aluminum cantilever beam is 40 cm in length and has a circular cross section with a…
A: The moment of inertia is-The young modulus for the aluminium part is-
Q: I want you to determine the forces between BC,CF and EF on the picture
A: Answer is in the Explanation Explanation:
Q: Please help. Please don't provide handwritten solution ...
A: The objective of the question is to calculate the unit volume change of an element of a material…
Q: What will happen to the points or pattern on a ternary phase diagram if temperature increases or…
A: A ternary phase diagram is a diagram which shows the phase behaviour of a system which consists of…
Q: A long circular shaft of length L with variable cross-section is fixed onto rigid walls as shown in…
A: The objective of the question is to find the angle of twist at different points of a long circular…
Q: A massless spring of spring constant 395 N/m is submerged in a viscous fluid wit damping constant b…
A: The spring constant is The damping constant is The mass of block is The initial displacement is The…
Q: +0.040 Holes of diameter 25.0+0.020 mm are assembled interchangeably with the pins of diameter…
A: To determine the minimum clearance in the assembly.
Q: 7. Find the distance a person can be from the wall and still be in equilibrium. Hanging mass = 21 kg…
A:
Q: What form of screw thread is most commonly used in the united states?
A: Here is the solution of your question:-Explanation:The most commonly used screw thread form in the…
Q: hd bending moment diagrams for the beam shown below 30 kN/m kN/m 1-KN A 2m 1 m 1M D
A: Draw shear force and bending moment diagrams for the beam shown below,
Q: Name: Surname: Student ID: ME 216 MECHANICS OF MATERIALS QUIZ # 2 QUESTION σ (MPa) 490 420 350 280…
A: According to our guidelines, we are supposed to answer the first three sub parts, Please repost…
Q: A syringe, containing an incompressible fluid, is oriented vertically and the plunger is slowly…
A: Given:At the maximum height point , velocity is zero.Hence, Assume the diameter at point is D and…
Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…
A: For the solution refer below images.
Q: A horizontal pipe is full of flowing water. At location A the velocity is 1.5 m/s and the…
A: The Pressure of the water at B is 133.43 kN/m3.Explanation:Given:v1 = Velocity at location A = 1.5…
Q: 5. The figure below shows a countershaft with helical gear (B), bevel gear (D), and two supporting…
A: For the surfaces in contact, the force that arises between mating gears is normal.Axial force Fa,…
Q: SITUATION 7: Three forces P1, P2, and P3 are acting on a semi-circular structure as shown in Fig.…
A: Given:The value of The value of The value of The value of The value of The value of The diagram for…
Q: In an air sample with a dry-bulb temperature of 28°C and a wet-bulb temperature of 22°C what is the…
A: To calculate relative humidity of dry bulb and wet bulb temperature
Q: Problem 4: A car body with mass m and pitching inertia I, is attached to the front and rear axles,…
A:
Q: In using the formula for measuring an American Standard Unified Screw Thread by the three-wire…
A: Here is the solution of your question:-Explanation:In the formula you provided for measuring an…
Q: Determine the Grashof condition and Barker Classification for the following mechanism, if d = 0.1 m,…
A: The solution is provided below step by step.
Q: For some metal alloy, a true stress of 345 MPa (50040 psi) produces a plastic true strain of 0.02.…
A: The step by step solution for this problem is shown below.
Q: Compute the coordinates of the centroid (x, y) of the area shown. лу 2013 Michael Swanbom CC +0 BY…
A:
Q: SITUATION 3: The Fig shows a circular steel plate supported on 3 posts A, B, and C which are equally…
A:
Q: Discuss the significance of Reynolds number in pressurized flow analysis ?
A: The Reynolds number () is a dimensionless quantity used to predict the flow regime of a…
Q: Determine the Grashof condition and Barker Classification for the following mechanism: 20 cm 40 cm…
A: Determine the Grashof condition and Barker Classification for the following mechanism:
Heat Exchangers
Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.
Heat Exchanger
The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.
Step by step
Solved in 3 steps with 3 images
- Q1] A shell and tube heat exchanger is used to heat water (C = 4236 J/kg. °C) from 80°C to 150°C at a rate of 12.5 kg/s by hot gas that enters the exchanger at 350°C with a rate of 20.36 kg/s. The overall heat transfer coefficient is 290 W/m² °C. The gas making 2-shell passes and the water making 4-tube passes. Calculate the heat transfer surface area (Cp (gas) = 1.04 kJ/kg.°C). heat flux: (a) byHello! I'd like help with the following exercise, from Levenspiel's "Engineering Flow and Heat Exchange". Leftover air at 20ºC and 100kPa is driven by a fan through a horizontal galvanized conduit of 1 m in diameter and 10m in length at a speed of 10 m/s. What size motor should be used if its efficiency is 90% and that of the fan is 20%? I'm not sure where to start. My professor hasn't explained much about this subject.in a 10-m long center-current flow tubular heat exchanger, a liquid food, flowing in the inner pipe (inside diameter 5 cm), is heated from 4 to 60 C for pasteurization. In the outer tube (diameter 10 cm), hot water enters at 95 C and exits at 80 C. A) If the mass flow rate of the hot water is 5 kg/s, what is the flow rate of the pasteurized product? The specific heat of the water is 4.2 kJ/(kg C), specific heat of product is 3.8 kJ/(kg C) B) what is the log mean temperature difference C) What is the overall heat transfer coefficient for the heat exchanger based on the outside surface?
- 2-) 10500 kg/hr of water is heated using a counter-flow, double-pipe heat exchanger utilizing superheated steam. Steam passes through the heat exchanger at 130 °C after entering at 180 °C. Water has an entrance temperature of 30 °C and an outlet temperature of 80 °C. Calculate the heat transfer area if the overall heat transfer coefficient from steam to water is 814 W/m² K. How much more area would there be if the fluid flow was parallel?5) During an experiment, a plate heat exchanger that is used to transfer heat from a hot-water stream to a cold-water stream is tested, and the following measurements are taken: Hot water Cold water stream stream 38.9 Inlet temperature, °C Outlet temperature, "C Volume flow rate, L/min 14.3 27.0 19.8 2.5 4.5 The heat transfer arca is calculated to be 0.0400 m. (a) Calculate the rate of heat transfer to the cold water. (b) Calculate the overall heat transfer coefficient. (c) Determine if the heat exchanger is truly adiabatic. If not, determine the fraction of heat loss and calculate the heat transfer efficiency. (d) Determine the effectiveness and the NTU values of the heat exchanger. (Answers: (a) 1724 W (b) 3017 Wiw C (c) the heat exchanger is not adiabatic so heat loss 16.4% and heat transfer efficiency 83.6% (d) effectiveness 44.4% and NTU 0.697) Hot water 38.9°C 19.8°C Cold water 14.3°C 27.0°CThe pressurized water that enters a cross-flow heat exchanger with a flow of 1 kg / s at 35 ° C and leaves at 125 ° C, where fluids do not mix, is heated by exhaust gases entering the heat exchanger at 300 ° C and exiting at 100 ° C. . The total heat transfer coefficient defined according to the surface on the gas side is 100 W / m ° K. Thermal properties of exhaust gases are considered as atmospheric air. a) Find the required surface area on the gas side. (15P) Due to the contamination that occurs over time, the inlet temperature and flow rate of the water in the heat exchanger remain the same, while the outlet temperature drops to 105 ° C *.a) Calculate the new condition with the acceptance of fixed thermal properties, b) Heat transfer, c) Exhaust gases exit temperature.
- 2-A cross-flow heat exchanger with both fluids unmixed is used to heat water (c, = 4.18 kJ/kg•K) from 40°C to 80°C, flowing at the rate of 1.0kg/s. What is the overall heat transfer coefficient if hot engine oil (c, = 1.9 kJ/kg-K), flowing at the rate of 2.6 kg/s, enters at 100°C? The heat transfer area is 20 m2. (Note %3D that you can use either an effectiveness or an LMTD method. It would be wise to use both as a check.)3.21 You must cool 78 kg/min of a 60%-by-mass mixture of glycerin in wa- ter from 108°C to 50°C using cooling water available at 7°C. Design a one-shell-pass, two-tube-pass heat exchanger if U = 637 W/m²K. Which side should the water flow through? Explain any design decision you make and report the area, TH₂0out and any other relevant features.Q2 a) Consider heat transfer to oil flow inside a copper pipe. Is the pipe length affecting the heat transfer rate into the oil? Briefly explain. b) Used engine oil can be recycled by a patented reprocessing system. Suppose that such a system includes a process during which engine oil flows through a 1-cm-internal diameter, 0.02-cm- wall copper tube at the rate of 0.05 kg/s. The oil enters at 35°C and is to be heated to 45°C by atmospheric-pressure steam condensing on the outside, as shown in figure given below. i) ii) iii) Determine the condensing steam temperature at 1 atm, T. [°C]. Calculate the convection heat transfer coefficient for the oil inside the pipe, [W/m'.K]. Calculate the rate of heat transfer rate into the oil, [kW], and, determine the length of the tube required. iv) Condensing steam Ct lam Oil in 35°C Oil out 0.05 kg/s I em 45°C 0.02 cm Copper tube L = ?
- 3.13 Air at 2 kg/s and 27°C and a stream of water at 1.5 kg/s and 60°C each enter a heat exchanger. Evaluate the exit temperatures if A = 12 m², U = 185 W/m²K, and: a. The exchanger is parallel flow; b. The exchanger is counterflow [Tħout = 54.0°C]; c. The exchanger is cross flow, one stream mixed; d. The exchanger is cross flow, neither stream mixed. [Thout = 53.62°C]4. The following heat exchanger uses 10 kg/s of hot air to heat and boil liquid water into saturated steam at 500 kPa. (a) Find the steam flow (kg/s) (b) Determine whether the process is allowed by the second law (Answer: It is not!) (c) On the surface, the process looks OK as Tair>Twater at both the inlet and outlet. You should be able to see the problem if you sketch the air and the water temperature profiles as you move left to right through the exchanger. (Hints: The air will be essentially a straight line, while the water will not. For the water, think about what happens when it is changing phase.) This is called a pinch point violation, and it is a very important design consideration in advanced combined cycle systems and in nuclear power plants. Air 100 kPa 160°C 10 kg/s Saturated Vapor 500 kPa Air: 160°C Steam: 151.8°C Q Air 100 kPa 30°C Liquid Water 500 kPa, 20°C Air: 30°C Water: 20°C3.36 Both C's in a parallel-flow heat exchanger are equal to 156 W/K, U 327 W/m²K and A = 2 m². The hot fluid enters at 140°C and leaves at 90°C. The cold fluid enters at 40°C. If both C's are halved, what will be the exit temperature of the hot fluid?