1) A simply supported beam made of elasto-plastic material and has a I shaped cross-section seen in the figure. If the yielding stress is o, = 240MP , determine the load that will cause collapse in the beam (Pcotlapse). Note: Consider the only bending effect in the calculations. 100 m 50 na 25 mm 200 mm 4 m 4 m 50 mm 250 mm

1) A simply supported beam made of elasto-plastic material and has a I shaped cross-section seen in the figure. If the yielding stress is o, = 240MP , determine the load that will cause collapse in the beam (Pcotlapse). Note: Consider the only bending effect in the calculations. 100 m 50 na 25 mm 200 mm 4 m 4 m 50 mm 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁
Question 3 A pair of lateral load is applied to a 3 m steel beam as in Figure Q3a to bend it plastically. The beam has a solid rectangular cross-section (30mm x 50mm) as in Figure Q3b. The steel behaves in elastic-perfectly plastic behavior with Yield Stress of 200 MPa. When 50% plastic condition at critical section, determine: a. the value of load P b. the Yielded Length, Lp corresponding to condition in part (a). 1.5P P 1m 1m Figure Q3a 1m 30mm 50mm Figure Q3b
The cantilever T- beam is loaded as shown in the figure. TE 80 mm 40 kN/m NA 120 mm 2.0 m Ina = 30x105 mm What is the value of maximum value of tensile flexural stress in MPa?
Determine the total deformation of a tapered bar with a thickness (t = 25 mm) as shown in the figure, having E= 200 x 103MP a. The applied load in the given problem is P = 220 kN. 25mm - B0mm P-220KN 750mm
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B; = 0.8 m; B; = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 B3 10KN 15KN 30KN
The beam shown in the figure below is subject to a moment of M = 17 kN.m as illustrated. Calculate the maximum tensile and compressive bending stresses. |-75 mm - - 12 mm B 12 mm 12 mm 75 mm 250 mm D 12 mm
A beam under load experiences sagging with a maximum bending moment of 24 x 106 Nm. The beam has a rectangular section (see Figure Q3b) where b = 35 mm and d = 65 mm. Calculate the maximum tensile stress and the maximum compressive stress for this beam.
Question 2 Figure Q2 shows a simply supported beam carrying two point loads. The beam has the cross-section shown. Calculate the maximum value of W that can be applied without overstress if the maximum allowable bending stress is 270 MPa and the maximum allowable shear stress is 15 MPa. 2W (kN) 3W (kN) 300 mm a. 6 m 3 m 2 m 100 mm
An aluminum bar having a cross-sectional area of 160 mm carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m: B2 = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 B3 ... 10KN 15KN 30KN A) 218.75 В 125 C 62.5 D) 31.25
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MРа. Aluminum A = 400 mm Bronze A = 200 mm Steel A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
For the beam geometry shown, determine the following: a. Cracking moment b. Has the beam section already cracked? c. Determine the bending stresses at the extreme fibers of the beam. Applied moment = 34kN/m fc = 21 MPa As = 1935mm² n=9 250mm 00 400mm 75mm