1) A compression spring has square edge and ground ends. The total coil number of spring is 12 and Brinell Hardness number is HB=380. The free length of the spring is 200 mm. The spring is assembled into a machine by compressing, when the machine runs, the spring is compressed 40 mm 18 n 100 mm. 10 mm a) Is the siring likely to buckled. b) Would this spring developed a permanent set if compressed solid? c) What is the critical frequency?

1) A compression spring has square edge and ground ends. The total coil number of spring is 12 and Brinell Hardness number is HB=380. The free length of the spring is 200 mm. The spring is assembled into a machine by compressing, when the machine runs, the spring is compressed 40 mm 18 n 100 mm. 10 mm a) Is the siring likely to buckled. b) Would this spring developed a permanent set if compressed solid? c) What is the critical frequency?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Design a compression helical spring to cary a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress 350 MPa Modulus of rigidity = 84 kN/mm2 4C – 1 + 4C – 4 0.615 Wahl's factor -, where C= spring index. [Ans. d= 5.893 mm; D=47.144 mm; n 6]
PROBLEM A 1) Find the equivalent spring, N/mm 2) Find the force, F k. Kl: =7 K5. =11 0000 K2 =8 X-10 mm k К3 -9 КА -10 К6 -12 ....... ........ .....
asap
It is required to design a helical torsion spring and Cold-drawn steel wire of Groele 4. The yitld strength the ultimate tensile strength, and the factor of Safety is 2. from space Considerations, the spring Per a window-shade. The is made of patented of the material is 60l. mean Coil. diameter is kept as 18 mm. The maximum be- Inding moment asting on the spring is e5oN-mm. The modulng of elas ticity of the kNlmm?). The stiffness of the rad). Determine the wire diameter and the um Coils. Also, detesmine the deflectino and stored struin.energy. spring spring moterial is (207 should be(3 N-mm/ berof active
A helical compression spring having 14 active coils is close coiled. It has a spring stiffness of 400lb/in. It is cut into two springs having 6 and 8 turns. Determine the spring stiffnesses of resulting springs.
A Helical Compression Spring is made of A232 Chrome-vanadium with squared and ground ends has wire diameter 5 mm, outer diameter 81.5 mm, free length 246.3 mm and total 10 turns. Do the analysis if the spring is safe and if not, what is the largest free length to which it can be wound using ns=1.2? Attach File Browse My Computer
1. Design a compression helical spring to carry a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress = 350 MPa Modulus of rigidity = 84 kN/mm2 4С - 1 0.615 Wahl's factor where C-spring index. 4С - 4
• Part A Tne 23 ky slercter rad is attaschext la a spring, which has an unetretches length ot 2 m. (Figure 1) If the roxt is released from est wher = 30", dalerine the argular velxcily of Ihr rod the inslant the spring becomes unstrrelched, rasurxt clockwise. Express your answer using three significant figures. Enter positive valuc if the angular velocity is clockwise and negative valuc if the angular velocity is counterclockwlse. vO AE 1t vec w = 3.32 rad/s Submit Previous Answeu Request Answer X Incorrect; Try Again; 5 attempts remaining Provide Feedback Next > Figure < 1 of 1
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
Problem A 1) Find the equivalent spring,N/mm 2) Find the force, F KI K5 k k K2 x=10 mim k 00000 0000 k КЗ K4 K6 ....... ...... ...... ...... ........... .. ........
Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside diameter should be limited to 66mm. if the permissible shear stress of the spring material is 325 N/mm? and the Modulus of rigidity is 85kN/mm?. a) Compute the deflection of spring per active turn and the axial load on the spring considering the effect of curvature, take Wahl's factor as Kw= 1.1 b) Calculate the value of axial load neglecting the effect of stress factor. **Note: Please upload your handwritten working/solution to the link provided. The value of Mean diameter of the spring in mm . The Spring Index is. Shear stress factor, neglecting curvature effect . Deflection per active turn in mm Axial Load W in N .. Axial Load W in N. considering effect of curvature .
A helical compression spring is wound using 0.12-in-diameter phosphor-bronze B159 wire. The spring index C = 10 and the total number of coils is N = 14. You may assume that the spring has both ends squared and ground and is supported between fixed ends. Also, Sgy = 0.45 · Sut- a. Estimate the spring rate. b. Estimate the static load corresponding to the yield strength. c. What should the free length of the spring be to ensure that when it is compressed solid the torsional stress does not exceed the yield strength? d. Calculate the critical value of the free length of the spring to avoid buckling.