0.5 in. EXAMPLE: 3. Nails having a total shear strength of 40lb are used in a beam that can be constructed either as in Case I or as in Case II (shown in the figure). If the nails are spaced at 9in, determine the largest vertical shear that can be supported in each case so that the fastener will not fail. (Practice at Home) Case 1 0.5 in Case II

0.5 in. EXAMPLE: 3. Nails having a total shear strength of 40lb are used in a beam that can be constructed either as in Case I or as in Case II (shown in the figure). If the nails are spaced at 9in, determine the largest vertical shear that can be supported in each case so that the fastener will not fail. (Practice at Home) Case 1 0.5 in Case II

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The hinge support at B, of beam AB shown below, has the magnified front view and side view shown. The pin connector has an allowable shear stress, Tallow, of 10 MPa. Determine the following: * The force in kN that will cause the double shear in the pin at B. * The minimum required diameter of the pin in millimetres. The value is a whole number * What if the pin was subjected to single shear, what would be the required diameter?
The beam is constructed from three boards. (Figure 1) The allowable shear stress for the wood is τallow=465 psiτallow=465 psi. Each nail can resist a shear force of 395 lblb. -Determine the maximum loads P that it can support. -What is the maximum allowable spacing ss of the nails used to hold the top flange to the web? (Consider only regions AC and BD.) -What is the maximum allowable spacing ss of the nails used to hold the bottom flange to the web? (Consider only regions AC and BD.)
TASK 3 250 180 14 I 30 24 Weld 450 A compound girder consists of a steel joist with steel plates welded onto each flange as shown. If the ends are simply supported and the effective span is 10 m, what is the maximum UDL which can be supported by the girder? [kN/m] Allowable longitudinal stress in plates = 110 MN/m² Allowable load in shear for each weld = 60 kN/m Allowable shearing stress in web of girder = 75 MN/m² Note: 1.0 MN/m² = 1.0 N/mm² 50
Practice 4.1.7 Two identical 20-mm - 200 mm thick plates are bolted to the top and bottom flange to form the built-up beam. 20 mm a) If the beam is subjected to a shear force of V = 250 kN, determine the allowable maximum spacing s of the bolts to the nearest mm. Assume each bolt has a shear 10 mm 300 mm capacity of 30KN, and I = 307.5E-6 m*. 10 mm b) What is the M, (plastic moment) of the beam assuming bolts can take infinite shear and o, = 250 MPai '10 mm 20 mm 200 mm
Q3) The beam system has a pin support at A, roller supports at D and F, and internal hinges at C. Find the deformations at C and E using the conjugate beam method. 10 kN A C D E F 100 kN-m k5 mt-5 m--5 m5 m-k10 m- = 100 x 10° mm*, and ICF Given: E = 200 GPa, IAC 50 x 10° mm“. %3D لقطة شاشة
4.) A thin plate PQR is deformed so that the corner Q is displaced downward 1.0 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges. 5) A pin mado of steo1 ie insorted in o short hanging TAOodon mombor ond iG 1used to Supnort lond E - 20
The wooden members A and B are to be joined by plywood splice plates, that will be fully glued on the surfaces in contact. As part of the design of the joint and knowing that the clearance between the ends of the members is to be 1/4 in., determine the smallest allowable length L if the average shearing stress in the glue is not to exceed 120 psi. 5.8 kips L. in. 4 in. B 5.8 kips Zoom image 11.28 in O 10.97 in 12.33 in
Is the beam cracked at service loads? The cracking moment is Mer Compute I, for the uncracked T-section (ignore the effect of the reinforcement for simplicity): Assume flange width = effective flange width from ACI Code Table 6.3.2.1= 66 in. (a) Compute the centroid of the cross section. Part Area (in.?) Ytop (in.) Aytop (in.³) Flange 66 X 5 = 330 2.5 825 Web 13 x 10 = 130 11.5 1495 Area = 460 in.? 2 Ay, = 2320 in. The centroid is located at 2320/460 = 5.04 in. below the top of the beam: Ytop = 5.04 in. y bottom = 12.96 in.
Situation 7:The figure shows a truss. The truss use angle bar for every members. Members BD and CD and CE are angle sections and needed to fasten to a gusset plate. with the thicknesses of 14 mm. The working stresses are 80 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets.. 4 m 4m 3 m MATHalino.com 4m 360 KN 19. How many 19 mm diameter rivets are needed to use for member BD. Number of rivets must express in whole number 20. How many 19 mm diameter rivets are needed to use for member CD 21. How may 19 mm diameter rivets are need to use for member CE
Two steel plates are welded together to form an inverted T-beam and are loaded as shown below. Determine the maximum bending stress developed. Also, determine the maximum shear stress at the neutral axis of the cross section. The following Inte Av = 9K Bv = 11K location of centroid = 3.56" above X-Ref Shear diagram Moment diagram 1" x 10" steel plate 1" x 8" steel plate X-reference A 6' 8K 12' 24' 12K 6' B of your work is accurate. Yo ment Mmax = 66K' Vmax 11K Moment of Inertia = 218 inª
P 62.5 mm Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55° inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the key in shear. If the block is loaded with P= 282 kN, calculate the required dimension "b" of the key. Write your final answer in 2 decimal places with the unit of mm.
The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3,080 mm^2. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.