10.32 a) Find the average power dissipated in the line in Fig. P10.32. b) Find the capacitive reactance that when con- nected in parallel with the load will make the load look purely resistive. c) What is the equivalent impedance of the load in (b)? d) Find the average power dissipated in the line when the capacitive reactance is connected across the load. e) Express the power loss in (d) as a percentage of the power loss found in (a). Figure P10.32 270/0° V (rms) Source- 1 6Ω Line j8Ω Τ 30 Ω j40 Ω Load

10.32 a) Find the average power dissipated in the line in Fig. P10.32. b) Find the capacitive reactance that when con- nected in parallel with the load will make the load look purely resistive. c) What is the equivalent impedance of the load in (b)? d) Find the average power dissipated in the line when the capacitive reactance is connected across the load. e) Express the power loss in (d) as a percentage of the power loss found in (a). Figure P10.32 270/0° V (rms) Source- 1 6Ω Line j8Ω Τ 30 Ω j40 Ω Load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
For maximum average power transfer in the circuit shown in the figure, set the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
Find the RMS line voltage VL at the source of the circuit. As shown the RMS load phase voltage is 100V and the line impedance is given in the figure.
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 H is operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ. Find: a) Draw the waveform of VTI and VR. b) Find the conduction angle (6). c) Calculate the RMS value of load current. d) Find the power factor e) What is the minimum value of a for which phase control is in effet. f) Find the size of the first three terms in the Fourier series for the current. T Zoom
For the following numeric values, determine theaverage power, P, the reactive power, Q, and the complex power, S, of the circuit shown in Figure. Note: phasor quantities are rms.
Draw the power factor triangle showing the different labelled sides. Illustrate a lagging power factor using a sinusoidal waveform. (d) List 2 negative effects of a poor power factor (e) How can a lagging power factor be corrected?
A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.
Which one of the following statements is true: The purpose of the power-factor correction is to add inductive elements to keep real power at a minimum level. The purpose of the power-factor correction is to add resistive elements (typically resistances) to improve the total reactive power. The purpose of the power-factor correction is to add reactive components (typically capacitive) to establish a system power factor closer to unity. The purpose of the power-factor correction is to add resistive elements (typically resistances) to establish a system power factor closer to zero.
For the system in the figure: Find the total average power, total reactive power, total apparent power, and total power factor. Find the current Is (in phasor form). If the loads can be modeled as a resistance in series with a reactive element (capacitor or inductor), find the impedance of each load. Confirm the result of part B using the input voltage and the result of part C. ..