0.3 The single stage, axialflow turbomachine shown in the figure involves water flow at a volumetric flowrate of 11 m'/s. The rotor revolves at 600 rpm. The inner and outer radii of the annular flow path through the stage are 0.46 and 0.61 m, and, B = 30°. The flow entering the rotor row and leaving the stator row is axial viewed from the stationary casing. Is this device a turbine or a pump? Estimate the amount of power transferred to or from the fluid. Q= 11 m

0.3 The single stage, axialflow turbomachine shown in the figure involves water flow at a volumetric flowrate of 11 m'/s. The rotor revolves at 600 rpm. The inner and outer radii of the annular flow path through the stage are 0.46 and 0.61 m, and, B = 30°. The flow entering the rotor row and leaving the stator row is axial viewed from the stationary casing. Is this device a turbine or a pump? Estimate the amount of power transferred to or from the fluid. Q= 11 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
Q3// the steam from the nozzle of single wheel impulse turbine discharges with velocity of 600 m/s at angle of 20°. The blade wheel rotates at 3000 rev/min and the mean blade radius is 590mm. the axial velocity of steam at exit from the blade (f.) is 164 m/s and the blades are symmetrical, calculate for 1 kg/s of steam: 1. The blades angles. 2. The blade power. 3. The blade efficiency. 4. The blade velocity coefficient. Answer (28°,126.3 kW, 70% ,0.799)
Situation XVII: A reservoir leads to 8 nozzles whose elevation is 210 m below that of the reservoir. The pipe leading to the nozzle is 1.80 m in diameter and 9000 m long with f = 0.015. The nozzle diameter is 100 mm with C = Cv = 0.92. %3D %3D 43. Find the velocity of the nozzle. a. 38.88 m/s b. 59.04 m/s c. 57.94 m/s d. 31.38 m/s 44. Find the head loss. a. 14.04 m b. 9.14 m c. 32.40 m d. 38.90 m 45. Find the aggregate horsepower available. a. 3687 hp b. 8190.10 hp c. 2402.40 hp d. 8504.04 hp
Q1): Impulse turbine diameter = 3.2m O1 = O2 Angular velocity = 25 rad/s Absolute velocities V1 = 140m/s and V2 = 110m/s Power developed by the wheel = 300kw Calculate: Jet 25mmd VI V: 1. the blade velocity. 2. the force exerted and 3. the angle O.
A Kaplan turbine of 100 B.H.P. is working under a headof 5 in and running at 210 R.P.M.The discharge through the tur.bine is 1*80 m°/sec.If now the turbine is allowed to work under a head of 15 m,what would be its new speed, discharge and power ?
A single jet Pelton turbine operates a 10,000 KW generator. The generator efficiency is 93%, turbine efficiency is 86%, turbine head is 350 m, coefficient of nozzle velocity is 0.98, speed ratio is 0.46 and the jet ratio is approximately 12. Find the size of the jet, mear diameter of runner, synchronous speed, specific speed of turbine and bucket dimensions.
Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m'/sec. 3. Specific speed.
1- A double jet of Pelton turbine driven by double nozzles to produce (4250 kw) to the shaft of an electrical generator when running at (400 rpm). The height of (180 m). wheel diameter is (1450 mm). The velocity of relative= 0.9 of jet velocity. If the angle of bucket is (165'), determine: a) Hydraulic efficiency b) Diameter of the jet
Asap
Q4/ An impulsive stage of a steam turbine is supplied with dry and saturated steam (15 da The stage has a single row of moving blades running at (3600 rpm). The mean diameter of the blade disc is (0.9 m). the nozzle angle is ( 15) and the axial component of absolute velocity leaving the nozzle is (94 m/sec). the height of the nozzles at their exit o mm). The nozzle efficiency is (0.9) and the blade velocity Coefficient is (0.97). The inles angie of the moving blades is (2°) greater than at the inlet. Determine, 1- the blade 4. thend the outlet angles. 2- the isentropic heat drop in the stage. 3- the stage efficiency. the power developed by the stage. th
A Pelton wheel works under a net head of 600 m and it runs at a speed of 720 rpm. The mean pitch dlameter of runner is 1.2 m. For a discharge rate of 0.2m/s, find the power available at the nozzle and hydraulle efficiency of turbine. Assume : C, = 0.98, side clearance angle of buckets = 20, Friction factor of bucket = 0.9.
Ans. [391.67 kW, 61.13 %] Problem (5.4) A nozzle in an impulse turbine delivers 1 kg/s steam to a set of blades moving at 200 m/s. The nozzles are inclined at an angle of 16° to the plane of the wheel. The blade velocity coefficient is 0.72, calculate the blade efficiency, work done and also estimate the energy V?. lost in the blades as; m° (-2).Take the blade angles at inlet and 2 outlet =25°. Ans. [76%,105 kW, 27.072 kW]