.(c) A brick masonry wall of size 450mm is carrying a load 120 kN/m. Find the depth of a RCC strip footing (i) (ii) (iii) (iv) (v) (vi) (vii) Depth of foundation: 1.20m Unit Weight of backfill: 16 kN/cum Net Allowable Bearing Pressure: 80 kN/m2 Unit Weight of R.C.C. : 24 kN/m2 Unit Weight of Brick Masonry: 19.8 kN/cum Grade of Concrete: M25 Grade of Steel : Fe-415

.(c) A brick masonry wall of size 450mm is carrying a load 120 kN/m. Find the depth of a RCC strip footing (i) (ii) (iii) (iv) (v) (vi) (vii) Depth of foundation: 1.20m Unit Weight of backfill: 16 kN/cum Net Allowable Bearing Pressure: 80 kN/m2 Unit Weight of R.C.C. : 24 kN/m2 Unit Weight of Brick Masonry: 19.8 kN/cum Grade of Concrete: M25 Grade of Steel : Fe-415

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. If the width of the bedplate is 3m and the clearance is 0.3 what is the upper width of the machine foundation
20. Determine the nominal load when the concrete strain of 0.003 and tensile steel strain is 0.002075. A. 1090 kN B. 1554 kN C. 1168 kN D. 1401 kN
A square footing 2.5m x 2.5 m supports a square column 300mm x 300mm at its center. Concrete cover to bar centroid = 100mm. Ultimate load combination is 1.2DL + 1.6L. Column loads aee service conditions: DL= 680 KN LL = 400KN f'c = 20.7 Mpa fy = 275 MPa Calculate the nominal punching-shear stress acting at the critical section of the footing slab if the thickness of the slab is 450 mm.
1. A square footing 1.6m x 1.6m having a thickness of 500 mm supports an interior 400 mmx400 mm square column is constructed by using f = 20.7 MPa normal-weight concrete and Grade-276 bars (fy = 276 MPa). The footing has 8-20mmo reinforcements, both ways and is terminated in 180° standard hook so that reinforcement may be assumed to be fully developed at the critical sections. The top of the footing will be covered with 500-mm of fill and 100-mm concrete thick basement floor. The basement floor loading is 2.4 kPa. Soil parameters: All = = 18 kN/m³, Ysoil = 16.5 kN/m³, = 30°, c = 0 kPa, Df = 2.0m. Use FS = 2.0 and assume general shear failure, determine the maximum service axial load (Pmax,service = PD + PL) that the footing can carry if PLIVE = 3PDEAD.
A square footing 2.5m x 2.5 m supports a square column 300mm x 300mm at its center. Concrete cover to bar centroid = 100mm. Ultimate load combination is 1.2DL + 1.6L. Column loads aee service conditions:DL = 680 kN LL = 400kNf'c = 20.7 Mpa fy = 275 MPa Calculate the nominal punching-shear stress acting at the critical section of the footing slab if the thickness of the slab is 450 mm. (Correct Answer 1.99)
4. A 2.10m x 2.10m footing carries concentrically a square column 0.40m x 0.40m. Design data: Column factored loads: DL = 570KN = 460KN %3D Concrete cover to the centroid of footing reinforcement = 110mm Concrete f'c - 21MPA Steel fy= 415MPA %3D %3D Allowable stresses at ultimate loads: For diagonal tension or two-way action shear = 1.52MPA For wide-beam shear 0.78MPA Maximum steel ratio for moment = 0.016 a. What is the minimum thickness (mm) of footing required for punching shear? b. Determine the minimum thickness (mm) of footing required for wide beam shear. Determine the minimum thickness (mm) of footing required for maximum moment. C.
A footing supports a 200mm thick concrete wall. = 175 Wall loads: Dead Load kN/m = 89 Live Load kN/m = 20.6 Concrete, f'c MPa = 415 Steel, fy MPa 23.6 Unit weight of concrete kN/m³ = 1.2D + Factored load combination 1.6L Thickness of footing 350mm Steel Cover (bottom of footing 90mm to centroid of bars) The gross allowable soil pressure is 100 kPa and width of the wall is 200mm. Assume that the top of the footing is at the ground level.
Design a square reinforced concrete footing to support a 20-inch square tied concrete column at the edge of the building as shown below. Also check development length and force transfer in the column and at the footing. Draw the reinforcement pattern. Use a footing thickness of 24". Assume the following design conditions: -service dead load= 270 kips -service live load= 135 kips -allowable soil pressure (q)= 5000 psf -f. for the column= 5000 psi -f. for the footing= 3000 psi -fy= 60000 psi -longitudinal column steel consists of #8 bars reinf cement is uncoated -unit weight of the soil is 125 lb/ft3 -normal weight concrete Finished ground line 20" square column Y = 125 lb/ft³ 5'
QUESTION 3 A footing of size 2.5 m x 2.5 m and 450 mm thick resists characteristics axial loads of 500KN dead and 200 kN imposed from a 300mm square column. The safe bearing pressure on the soil is 230kN/m?. a. Check whether the base pressure is safe b. Design the bending reinforcement, assuming 16mm diameter bars c. Check the punching shear Further Design Information Characteristic strength of concrete (fm) = 35 N/mm? %3D Characteristic yield stress of steel (f;) 460 N/mm2 Cover to reinforcement = 75 mm Diameter of main bars = 16 mm Unit weight of concrete = 24 kN/m³
C9-1. The concrete footing A was poured when this oolumn was put in place. Later the rest of the foundation stab was poured. Can you explain why the 45° cracks occured at cach corner? Can you think of a better design that would avoid such cracks?
roportion a trapezoidal combined footing for uniform pressure under dead load plus reduced live load with the following data in table. Distance c/c of column is 6 m and projection beyond column not exceed 0.5 m DL+Reduce dLL=175Kn/m2 DL+LL=230KN/m2 columnA DL=620KN LL=390KN column B DL=670KN LL=815KN
5-A 10ft continuous flexible strip footing is subjected to a load of 500 psf. Find the change in stress A - Below a point 3ft deep and 6ft perpendicular to the center of footing. B - Below the edge of the foundation at a depth of 3ft. C - Below the center of the footing at a depth of 3ft.