. A 10 mm thick steel tank has an outside diameter of 500 mm and a length of 4m. It is subjected to an internal pressure of 10000 kPa. a) Determine the circumferential stress in the tank. b) Find the longitudinal stress in the tank. c) To what value could the internal pressure be increased if the allowable design stress is 110 MPa?

. A 10 mm thick steel tank has an outside diameter of 500 mm and a length of 4m. It is subjected to an internal pressure of 10000 kPa. a) Determine the circumferential stress in the tank. b) Find the longitudinal stress in the tank. c) To what value could the internal pressure be increased if the allowable design stress is 110 MPa?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pressure vessel, 320 mm in diameter is to be fabricated from steel plates. The vessel is to carry an internal pressure of 4MPa. a.) What is the required thickness in mm of the plate if the vessel is to be spherical. Allowable stress is 120 MPa. b.)The vessel to be fabricated is a cylinder using 12 mm thick steel plating. What is the maximum internal pressure that the vessel can carry if theallowable steel stress is 60 MPa. c.)Find the required thickness of the plate if the vessel is to be cylindrical. The allowable stress is 120 MPa.
Given: The infinitesimal “happy-little-cube™" with stresses shown. Determine: Draw Mohr's circle for the stress shown, label a) max and min principal stresses, b) max shear stress, c) center and d) plot the stress state shown on the circle 12 ksi Show all work. Do not calculate any angles! 6 ksi
The state of stress shown to the left was produced by a combination of loadings on a body that is not shown. Determine the following via Mohr's circle: A) Draw Mohr's Circle for the x-y plane. B) Determine the principal stresses - All 3. C) Sketch a properly oriented differential element showing the principal stresses in the x-y plane. D) Determine the magnitude of the maximum shear stress in the x-y plane. E) Sketch a properly oriented differential element showing the maximum shear stress state in the x-y plane. F) Determine the magnitude of the absolute maximum shear stress (and include the two out of plane circles on your original figure). Use the following values for the magnitudes of the stresses: x = 0₂ Txy Ox X X 10 ksi, σy = 4 ksi, σ₂ = 3 ksi, Txy = 4 ksi
Q2) A shaft rotating at 350 r.p.m. drives another shaft at 550 r.p.m. and transmits 10.5 kW through a belt. The belt is 80 mm wide and 9.5 mm thick. The distance between the shafts is 3.8 m. The smaller pulley is 9 cm in diameter. Calculate the stress in the belt, if it is across belt drive. Take u = 0.3.2. (30 degrees) Q3
Direct stresses of 160N/mm2 tensile and 120 N/mm2 compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm2. a) What must be the magnitude of the shearing stresses on the two planes? b) What will be the maximum shearing stress at the point?
A closed cylindrical vessel made of steel plate 10 mm thick, with a plain ends carries fluid under a pressure of 20 N/mm², The diameter of cylinder is 400 mm and the length is 1500 mm. The steel plate young's modulus is 180000 N/mm² with a poisons ratio of .3 ,Determine the following a) The hoop stress in the cylinder wall b) The diameter change c) The change in Length
A round solid bar has a diameter of 30mm. A tensile force of 120kN is applied at the centroid of area . A) Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line[ANS : 170 MPa] B) The force in Q1 is re-applied to the same round solid bar but 5mm above the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line[ANS:+396, -56 MPa] HOW to answer part two I did not get the answer !!
Asap
In one specific point in a structure, the stress state is as pictured on the differential element. Calculate a) Principal stresses and their angle of orientation b) Absolute maximum shear stress. 200 MPa 100 MPa 300 MPa
For the given system;a) Draw internal force diagrams and determine the most critical section.b) Show the stress distribution on this critical section and find the maximum normal stress.GIVEN: ℓ1 = 80 cm, ℓ2 = 40 cm, M = 8000 Ncm, b = 4 cm, h = 6 cm, t = 1 cm, F = 1400 N, qo = 30 N/cm .
2. In one specific point in a structure, the stress state is as pictured on the differential element. Calculate a) Principal stresses and their angle of orientation b) Absolute maximum shear stress.
a) A pipe with an inside diameter of 42 mm is subjected to an axial load of 850 kN. If the maximum allowable tensile stress in the pipe is 2.50 kN/mm², calculate the minimum wall thickness required for the pipe. Give your answer in millimetres (mm) to 2 decimal places. b) A 1.25 m long cable has a diameter 3.50 mm with a Young's Modulus, E, of 9.75 x 10⁹ N/m². When the wire is placed under tension, it experiences a stress of 202.52 x 106 N/m², the length of the cable extends by 36.35 mm. Calculate the force that the cable experiences under tension and the strain energy density (U/V) due to deformation. Give your answers in newtons (N) to 2 decimal places for the force; and in joules per cubic metre (J/m³) for the strain energy density to 2 decimal places. Assume the cable is solid and the material is homogeneous. c) Figure Q1c shows a bracket on rollers that allow the bracket to move along a beam in the horizontal direction. A force F₁ of 2625 N acts at point A where the angle 8…