Two members of uniform cross section 65 x 95 mm are glued together along Plane a-a that forms an angle of 15° with the horizontal. Knowing that the allowable stresses for the glued joint are o = 825 kPa and t = 400 kPa, determine the largest centric load P that can be applied. You may either use stress transformation equations or Mohr's circle. 65 mm a P a 15° P 11 kN

Two members of uniform cross section 65 x 95 mm are glued together along Plane a-a that forms an angle of 15° with the horizontal. Knowing that the allowable stresses for the glued joint are o = 825 kPa and t = 400 kPa, determine the largest centric load P that can be applied. You may either use stress transformation equations or Mohr's circle. 65 mm a P a 15° P 11 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
7. Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches and the bar weigh 6kips. Figure P-106 3 m 5 m 5 m E
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The diameter of rod (1) is d1 = 1.66 in. and the diameter of rod (2) is d2 = 2.68 in. Determine the normal stresses in rods (1) and (2). Assume P = 17 kips and Q = 29 kips. Use positive for tensile stress and negative for compressive stress.
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e� = 55 mmmm and is subjected to the loading shown. Let a� = 200 mmmm , b� = 220 mmmm , c� = 350 mmmm , d� = 250 mmmm , and P� = 3.0 kNkN . Take point A to be at the top of the circular cross-section. As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, Mx��. b) Part B - Moment about the z axis at A Part C - Stress due to the normal force To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the normal force. Part D - Stress due to the bending moment about the x axis To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm , find the stress σA�� due to the bending moment about the x axis.
The collar bearing shown is subject to a 500 kN force. 500 kN The collar is 25 mm thick. Find d and D (to the nearest mm) so that the allowable normal stress in the column collar bearing of o = 280 MPa, the allowable shear stress in the collar collar of t = 200 MPa and the allowable bearing stress between the collar and the support of ob = 70 MPa is not exceeded.
1 m Section of connection for AB and BC 1m An elbow shaped frame made of Al 2024 T6 aluminum has a circular cross-section having a radius of 5mm. a. Take a cut through the section where the AB and BC segments are connected (shown in the figure at point B). Define the stress types that will occur on this section as a result of loading on the frame and show the variation of these stresses on the cross-section. b. Drawing a free body diagram, show and calculate the internal loads at point C. Show the stress distribution that are caused by these internal loads on this cross-section. Do the internal loads vary along the beam BC ?
Two blocks joined by a single pin are subjected to a pulling force of P = 250 Ib. The pin has a diameter of 0.25 in and the dimensions of the blocks with respect to the figure below are listed below. a = 2.42 in b = 1.52 in C = 1.5 in ti = 0.89 in t2 = 1.2 in Note that the dimensions b and c represent the distance from the edge of the block to the middle of the pin t, 1 a Vinter201920-Engr220-001/images/9de8f780-b478-3fb6-91f7-bd1015381538_fafc4bb4-e5d Image is not drawn to scale.
The rectangular piece of wood, 50 mm by 100 mm, is used as a compression block. The grain of the wood makes a 20° angle with the horizontal, as shown in Figure 2. Determine the largest axial force P that can be applied safely if the allowable stresses on the plane of the grain are 20 MPa for compression and 5 MPa for shear. IP 20°
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
25 kN 25 KN 12 mm 18 mm 1.55 The lap joint is fastened with four 3/4-in.-diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. 7.5 mm 25 KN 7.5 mm 4 in. in. 25 KN 12 mm 12.5 mm FIG. P1.54 18 mm 78 in. FIG. P1.55 78