The steel pipe in (Eigure 1) has an inner diameter of 3.54 in, and an outer diameter of 3.79 in. Figure 12 in 12 in. 1 of 1 60 lb If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. VE] ΑΣΦ | it voc 1, Submit Provide Feedback Request Answer ? psi, psi Next

The steel pipe in (Eigure 1) has an inner diameter of 3.54 in, and an outer diameter of 3.79 in. Figure 12 in 12 in. 1 of 1 60 lb If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. VE] ΑΣΦ | it voc 1, Submit Provide Feedback Request Answer ? psi, psi Next

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The steel pipe in (Figure 1) has an inner diameter of 4.57 in. and an outer diameter of 4.82 in. Figure 12 in. 12 in. 1 of 1 > 60 lb Part A If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. 01, 02 = Submit Provide Feedback Request Answer pai, psi Next >
The steel pipe in (Figure 1) has an inner diameter of 3.41 in and an outer diameter of 3.66 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe.
Determine the stresses at points A and B as a results of applying each of the following internal loads N = 300 N, V = 250 N, M = 120 N.m and T = 300 N/m. The diameter is 20 mm. You must show your detailed solutions
The thin-walled pipe has an inner diameter of 2 in. and a thickness of 0.1 in. It is subjected to an internal pressure of 530 psi and the axial tension and torsional loadings shown in (Figure 1). Suppose that M = 240 lb. ft. 900 lb- M M 900 lb Part A Determine the in-plane principal stresses at a point on the surface of the pipe. Express your answers in kilopounds per squared inch to three significant figures separated by a comma. 17 ΑΣΦ 01,02 = vec ? ksi
The vertical force P acts on the bottom of the plate having a negligible weight. Determine the shortest distance d to the edge of the plate at which it can be applied so that it produces no compressive stresses on the plate at section a-a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness. a 200 mm- d 300 mm a 500 mm
A steel pipe (E1=200 GPa) surrounds a solid aluminum-alloy rod (E2 =70 GPa), and together they are subjected to a compressive force of 200 kN acting on rigid end caps. Determine the shortening of this metallic compression member, and determine the normal stresses in the pipe and in the rod.
For the plane-stress condition given below: σx = 400 MPa σy = 500 MPa τxy = - 30 MPa Construct a Mohr’s circle of stress, find: (a) the principal stresses and the orientation of the principal axes relative to the x,y axes (b) determine the stresses on an element, rotated in the x-y plane 60° counter?clockwise from its original position ; Show these stresses on a sketch of an element oriented at this angle (c) Also, using the matrix transformation law to compare the solutions with Mohr’s circle
The principal strains at a point on the aluminum surface of a tank are P1 = 630(10-6) and P2 = 350(10-6). If this is a case of plane stress, determine the associated principal stresses at the point in the same plane. Eal = 10(103) ksi,nal = 0.33.
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 16 MPa in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the stresses σn, σt, and the magnitude of τnt and show them on a stress element that is properly rotated with respect to the x-y element. The sketch must include the magnitude of the angle between the x and n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise).
5. Segment AB of the bar is a tube with an outer diameter of d1 and a wall thickness of 0.125 in. Segment BC is a solid rod of diameter d2. The average normal stresses must not exceed 3400 psi in rod AB and 6500 in rod BC, respectively. Use P1 = 3,600 lb. and P2 = 5,500 lb. 0.125 in. di В A 6 in.- 6 in. Determine the smallest allowable value of d1 (in inches). Round-off to 2-decimal places. Your answer Determine the smallest allowable value of d2 (in inches). Round-off to 2-decimal places. Your answer Вack Next Clear form Never submit pas swords through G0ogle Forms
Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal stress. Specify the orientation of the element in each case